Home › Engine / Hybrid System › 2NR-FE ENGINE CONTROL › SFI SYSTEM › from 2018.01
RM30M0E _51 Engine / Hybrid System _053304 2NR-FE ENGINE CONTROL _0258353 SFI SYSTEM J

2NR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually:

When the ignition switch is turned ON, the MIL should be illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A415045E03
0.708,2.094 1.146,2.25 0.438,0.156 10 false F38 0.688,2.271 2.583,2.5 1.896,0.229 10 false Combination Meter Assembly 2.01,0.896 2.49,1.083 0.479,0.188 10 false CANH 2.031,1.594 2.51,1.781 0.479,0.188 10 false CANL 4.792,0.896 5.271,1.083 0.479,0.188 10 false CANH 4.813,1.615 5.292,1.802 0.479,0.188 10 false CANL 2.531,0.688 2.854,0.906 0.323,0.219 10 false 23 2.521,1.406 2.844,1.625 0.323,0.219 10 false 22 4.479,0.698 4.802,0.917 0.323,0.219 10 false 13 4.51,1.406 4.833,1.625 0.323,0.219 10 false 14 0.969,3.417 2.865,3.646 1.896,0.229 10 false : CAN Communication Line 5.365,2.104 5.802,2.26 0.438,0.156 10 false F130 5.365,2.271 5.802,2.427 0.438,0.156 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
Result Condition Proceed to
Illuminates → Turns off Ignition switch ON → After engine is started A
Other than above - B




A

B

2.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

4.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)

B

4.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Indicator
50004 122 150

e.

Check the status of the MIL while performing the Active Test.

Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY