Use the same procedure for both the LH and RH sides.
The procedure described below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (for Hatchback).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67492A
3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Disengage the 2 clips and remove the front door lower frame bracket garnish.
74220
4.REMOVE FRONT ARMREST ASSEMBLY
Disengage the 8 claws, 3 clips and 4 guides.
Disengage in order from the front of the vehicle.
| *1 | Retainer |
Disengage the retainer to remove the front armrest assembly.
74232
5.REMOVE FRONT ARMREST BASE UPPER PANEL
Disengage the 8 claws, 2 clips and 4 guides.
Disengage in order from the rear of the vehicle.
for Driver Side:
Disconnect the 2 connectors and remove the front armrest base upper panel.
for Front Passenger Side:
Disconnect the connector and remove the front armrest base upper panel.
67602
6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the door inside handle bezel plug.
Remove the 3 screws.
Disengage the 8 clips.
Disengage the guide and the 5 claws.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
Disengage the 2 guides, disconnect the front door lock remote control cable assembly and front door inside locking cable assembly and remove the front door trim board sub-assembly.
69206B
7.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the 4 guides and remove the front door inside handle sub-assembly from the front door trim board sub-assembly.
86160
8.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
87940
9.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
68210C
10.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
75756C
11.REMOVE FRONT DOOR WINDOW FRAME REAR MOULDING
75922M
12.REMOVE NO. 1 BLACK OUT TAPE (w/ Black Out Tape)
68172A
13.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
Remove the front door glass inner weatherstrip.
67832
14.REMOVE FRONT DOOR SERVICE HOLE COVER
Remove the front door service hole cover.
Remove any butyl tape remaining on the front door panel side.
68102
15.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Connect the power window regulator master switch assembly.
Connect the cable to the negative (-) battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the power window regulator master switch assembly.
Remove the 2 bolts.
Do not damage the front door glass sub-assembly.
Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.
Do not damage the front door glass sub-assembly.
68151D
16.REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
67664C
17.REMOVE DOOR FRAME GARNISH
Disengage the clamp and remove the door frame garnish.
69820
18.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
| *a | Temporary Bolt |
Disconnect the connector.
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.
Remove the 5 bolts and the front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
67924
19.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION
| *a | Double-sided Tape |
Remove the 2 bolts.
Peel off the double-sided tape and remove the front door No. 2 stiffener cushion.
Remove any double-sided tape remaining on the front door panel side.
67404F
20.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Remove the 2 bolts.
Disengage the guide and remove the front door rear lower frame sub-assembly.
69217D
21.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (w/ Lock Cylinder)
| *1 | Hole Plug |
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder.
Disengage the claw and guide to remove the front door outside handle cover from the lock cylinder.
69217D
22.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (w/o Lock Cylinder)
| *1 | Hole Plug |
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the 2 claws and remove the front door outside handle cover.
69320
23.REMOVE FRONT DOOR LOCK ASSEMBLY
69220
24.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)
w/ Smart Entry and Start System:
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws to open the cover as shown in the illustration.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.
Remove the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.
69220
25.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side)
Remove the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.
69241H
26.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD
Disengage the 2 claws and guide to remove the front door outside handle front pad.
69242E
27.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD
Disengage the 2 guides to remove the front door outside handle rear pad.
69202A
28.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (for Driver Side)
w/ Smart Entry and Start System:
| *a | Clamp |
| *b | Guide |
| *c | Grommet |
Using a clip remover, disengage the clamp.
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the grommet and guide to disconnect the front door outside handle frame sub-assembly with wire harness in the direction indicated by the arrow as shown in the illustration.
| *a | Clamp |
| *b | Guide |
Disengage the 2 clamps and guide to remove the front door outside handle frame sub-assembly.
w/o Smart Entry and Start System:
| *a | Grommet |
| *b | Guide |
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the grommet and guide to remove the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.
69202A
29.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (for Front Passenger Side)
| *a | Grommet |
| *b | Guide |
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the guide and remove the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.
69312
30.REMOVE FRONT DOOR LOCK OPEN ROD
| *a | Snap Ring |
Disengage the snap ring as shown in the illustration.
Remove the front door lock open rod from the front door handle frame sub-assembly.
67001A
31.REMOVE FRONT DOOR PANEL CUSHION
Remove the 2 front door panel cushions.
68610
32.REMOVE FRONT DOOR CHECK ASSEMBLY
Remove the 3 bolts and the front door check assembly.
67862
33.REMOVE FRONT DOOR WEATHERSTRIP
Using a clip remover, remove the clip.
Using a clip remover, disengage the clip A and 14 clips and remove the front door weatherstrip.
75792
34.REMOVE DOOR WINDOW FRAME MOULDING CLIP
Using a clip remover, disengage the claw to remove the door window frame moulding clip.
67837B
35.REMOVE FRONT DOOR DUST PROOF SEAL
Disengage the 3 claws to remove the 3 front door dust proof seals.