Refer to DTCs C1401 and C1402.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH) |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH) |
| C1413 | Front Speed Sensor RH Output Malfunction | Either of the following is detected:
1.
An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more. 2.
At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds. 3.
At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more. |
·
Front speed sensor rotor RH (Front axle hub sub-assembly RH) ·
Sensor installation ·
Skid control ECU (Brake actuator assembly) |
| C1414 | Front Speed Sensor LH Output Malfunction | Either of the following is detected:
1.
An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more. 2.
At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds. 3.
At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more. |
·
Front speed sensor rotor LH (Front axle hub sub-assembly LH) ·
Sensor installation ·
Skid control ECU (Brake actuator assembly) |
Refer to DTCs C1401 and C1402.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Open | Front speed sensor RH open detection | Normal or Error | Normal | Error: Momentary interruption |
| FL Speed Open | Front speed sensor LH open detection | Normal or Error | Normal | Error: Momentary interruption |
| Tester Display |
|---|
| FR Speed Open |
| FL Speed Open |
Normal (There are no momentary interruptions.)
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
The front speed sensor rotor is incorporated into the front axle hub sub-assembly. If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly with front speed sensor.
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
All Test Mode DTCs are cleared.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| A |
| B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector and the A14 and/or A13 front speed sensor connectors.
*1: except LHD with Continuously Variable Transaxle
*2: for LHD with Continuously Variable Transaxle
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-7 (FR+) - A14-2 (FR+) | Always | Below 1 Ω |
| A48-6 (FR-) - A14-1 (FR-) | Always | Below 1 Ω |
| A48-7 (FR+) or A14-2 (FR+) - Body ground | Always | 10 kΩ or higher |
| A48-6 (FR-) or A14-1 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-7 (FR+) - A14-2 (FR+) | Always | Below 1 Ω |
| A49-6 (FR-) - A14-1 (FR-) | Always | Below 1 Ω |
| A49-7 (FR+) or A14-2 (FR+) - Body ground | Always | 10 kΩ or higher |
| A49-6 (FR-) or A14-1 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-19 (FL+) - A13-2 (FL+) | Always | Below 1 Ω |
| A48-18 (FL-) - A13-1 (FL-) | Always | Below 1 Ω |
| A48-19 (FL+) or A13-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| A48-18 (FL-) or A13-1 (FL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-19 (FL+) - A13-2 (FL+) | Always | Below 1 Ω |
| A49-18 (FL-) - A13-1 (FL-) | Always | Below 1 Ω |
| A49-19 (FL+) or A13-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| A49-18 (FL-) or A13-1 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Front Speed Sensor) |
| *b | for RH |
| *c | for LH |
Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.
*1: except LHD with Continuously Variable Transaxle
*2: for LHD with Continuously Variable Transaxle
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A14-2 (FR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A13-2 (FL+) - Body ground | Ignition switch ON | 8 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs (C1413 and C1414) are not output | A |
| DTCs (C1413 and/or C1414) are output | B |
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Replace the front axle hub sub-assembly.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
The front speed sensor rotor is incorporated into the front axle hub sub-assembly.
If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly with front speed sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs (C1413 and C1414) are not output | A |
| DTCs (C1413 and/or C1414) are output | B |
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
A
B