Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1277  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1415  Rear Speed Sensor RH Output Malfunction  C1416  Rear Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1403 and C1404.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273

DTC No. Detection Item DTC Detection Condition Trouble Area
C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)

·

Rear speed sensor rotor (Rear axle hub and bearing assembly RH)


C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)

·

Rear speed sensor rotor (Rear axle hub and bearing assembly LH)


C1415 Rear Speed Sensor RH Output Malfunction Either of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Skid control sensor wire RH

·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector


C1416 Rear Speed Sensor LH Output Malfunction Either of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Skid control sensor wire LH

·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Normal or Error Normal Error: Momentary interruption
RL Speed Open Rear speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
HINT:

Perform the above inspection before removing the sensor and connector.


OK:

Normal (There are no momentary interruptions.)


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

6.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4
f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG



OK

3.PERFORM TEST MODE (SIGNAL CHECK)

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check in the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1415 and/or C1416 are output A
DTCs C1415 and C1416 are not output B



A

B

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
5.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C118693C01
0.676,0.188 0.859,0.363 0.183,0.176 10 *a 2.229,0.188 2.412,0.363 0.183,0.176 10 *b 1.738,1.666 1.923,1.836 0.185,0.17 10 *c
*a Normal
*b Abnormal
*c Clearance


Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL SENSOR WIRE

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

6.INSPECT SKID CONTROL SENSOR WIRE
a.

Remove the skid control sensor wire.


b.
C280125C17
0.823,0.49 1.167,0.667 0.344,0.177 0.823,0.74 1.167,0.917 0.344,0.177 2.167,0.5 2.583,0.677 0.417,0.177 2.167,0.75 2.583,0.927 0.417,0.177 0.948,1.542 0.667,2.396 true 1.104,1.552 1.333,2.385 true 2.333,1.667 2.083,2.385 true 2.5,1.667 2.823,2.375 true 0.135,0.125 0.323,0.323 0.188,0.198 10 false *a 0.917,0.5 1.167,0.667 0.25,0.167 10 false P1 0.917,0.75 1.156,0.917 0.24,0.167 10 false O1 2.25,0.75 2.583,0.917 0.333,0.167 10 false OF1 0.5,2.417 1,2.583 0.5,0.167 10 false RR- *b 1.25,0.75 1.438,0.917 0.188,0.167 10 false *c 2.667,0.75 2.833,0.917 0.167,0.167 10 false *c 2.646,0.5 2.833,0.667 0.188,0.167 10 false *b 1.25,0.5 1.438,0.667 0.188,0.167 10 false *b 2.25,0.5 2.583,0.667 0.333,0.167 10 false PF1 0.5,2.583 1,2.75 0.5,0.167 10 false RL- *c 1.167,2.417 1.667,2.583 0.5,0.167 10 false RR+ *b 1.167,2.583 1.667,2.75 0.5,0.167 10 false RL+ *c 1.917,2.417 2.417,2.583 0.5,0.167 10 false RR+ *b 1.917,2.583 2.417,2.75 0.5,0.167 10 false RL+ *c 2.667,2.417 3.167,2.583 0.5,0.167 10 false RR- *b 2.667,2.583 3.167,2.75 0.5,0.167 10 false RL- *c
*a Component without harness connected
(Skid Control Sensor Wire)
*b for RH
*c for LH


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
P1-2 (RR+) - PF1-1 (RR+) Always Below 1 Ω
P1-1 (RR-) - PF1-2 (RR-) Always Below 1 Ω
P1-2 (RR+) - PF1-2 (RR-) Always 10 kΩ or higher
P1-2 (RR+) or PF1-1 (RR+) - Body ground Always 10 kΩ or higher
P1-1 (RR-) - PF1-1 (RR+) Always 10 kΩ or higher
P1-1 (RR-) or PF1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
O1-2 (RL+) - OF1-1 (RL+) Always Below 1 Ω
O1-1 (RL-) - OF1-2 (RL-) Always Below 1 Ω
O1-2 (RL+) - OF1-2 (RL-) Always 10 kΩ or higher
O1-2 (RL+) or OF1-1 (RL+) - Body ground Always 10 kΩ or higher
O1-1 (RL-) - OF1-1 (RL+) Always 10 kΩ or higher
O1-1 (RL-) or OF1-2 (RL-) - Body ground Always 10 kΩ or higher



c.

Install the skid control sensor wire.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

REPLACE SKID CONTROL SENSOR WIRE

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



d.

Disconnect the P1 or O1 rear speed sensor connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (except LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A48-17 (RR+) - P1-2 (RR+) Always Below 1 Ω
A48-17 (RR+) or P1-2 (RR+) - Body ground Always 10 kΩ or higher
A48-16 (RR-) - P1-1 (RR-) Always Below 1 Ω
A48-16 (RR-) or P1-1 (RR-) - Body ground Always 10 kΩ or higher

for RH (for LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A49-17 (RR+) - P1-2 (RR+) Always Below 1 Ω
A49-17 (RR+) or P1-2 (RR+) - Body ground Always 10 kΩ or higher
A49-16 (RR-) - P1-1 (RR-) Always Below 1 Ω
A49-16 (RR-) or P1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH (except LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A48-5 (RL+) - O1-2 (RL+) Always Below 1 Ω
A48-5 (RL+) or O1-2 (RL+) - Body ground Always 10 kΩ or higher
A48-4 (RL-) - O1-1 (RL-) Always Below 1 Ω
A48-4 (RL-) or O1-1 (RL-) - Body ground Always 10 kΩ or higher

for LH (for LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A49-5 (RL+) - O1-2 (RL+) Always Below 1 Ω
A49-5 (RL+) or O1-2 (RL+) - Body ground Always 10 kΩ or higher
A49-4 (RL-) - O1-1 (RL-) Always Below 1 Ω
A49-4 (RL-) or O1-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.

Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



b.

Turn the ignition switch off.


c.
C280123C34
0.76,0.365 1.198,0.604 0.438,0.24 2.344,0.375 2.781,0.615 0.438,0.24 1.344,1.729 1.063,1.24 true 2.917,1.719 2.646,1.24 true 1.292,0.396 1.49,0.594 0.198,0.198 10 false *b 0.875,0.406 1.094,0.604 0.219,0.198 10 false P1 2.469,0.406 2.688,0.594 0.219,0.188 10 false O1 2.875,0.385 3.073,0.583 0.198,0.198 10 false *c 0.115,0.104 0.313,0.302 0.198,0.198 10 false *a 2.979,1.677 3.313,1.865 0.333,0.188 10 false RL+ 1.417,1.698 1.75,1.885 0.333,0.188 10 false RR+
*a Front view of wire harness connector
(to Rear Speed Sensor)
*b for RH
*c for LH


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
P1-2 (RR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
O1-2 (RL+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.



Result:
Proceed to
OK
NG



OK

9.RECONFIRM DTC

NG

9.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


d.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs (C1415 and C1416) are not output A
DTCs (C1415 and/or C1416) are output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



A

B

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the rear axle hub and bearing assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB(for Rear Drum Brake)>REMOVAL

NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.



Result:
Proceed to
NEXT



NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


d.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs (C1415 and C1416) are not output A
DTCs (C1415 and/or C1416) are output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



A

END

B