Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering angle sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1432 Steering Angle Sensor Power Source Voltage Malfunction Steering angle sensor power supply malfunction signal is received from steering angle sensor.
·

DOME fuse

·

IG1 NO. 2 fuse

·

Steering angle sensor

·

Wire harness or connector



WIRING DIAGRAM

C375659E04
0.156,4.729 0.771,4.927 0.615,0.198 10 false F147 0.156,4.896 3.365,5.094 3.208,0.198 10 false Steering Angle Sensor 0.563,5.375 2.344,5.625 1.781,0.25 10 false : CAN Communication Line 0.75,0.708 1.365,0.906 0.615,0.198 10 false CANH 6.01,0.708 6.625,0.906 0.615,0.198 10 false CANH 0.771,1.302 1.385,1.5 0.615,0.198 10 false CANL 6,1.281 6.615,1.479 0.615,0.198 10 false CANL 5.333,0.719 5.792,0.917 0.458,0.198 10 false A48 5.344,1.302 5.802,1.5 0.458,0.198 10 false A48 5.656,0.719 6.115,0.917 0.458,0.198 10 false A49 5.656,1.302 6.115,1.5 0.458,0.198 10 false A49 5.688,0.521 6,0.719 0.313,0.198 10 false 25 5.375,0.521 5.688,0.719 0.313,0.198 10 false 25 5.365,1.115 5.677,1.313 0.313,0.198 10 false 14 5.698,1.115 6.01,1.313 0.313,0.198 10 false 14 5.385,0.917 5.698,1.115 0.313,0.198 10 false *1 5.385,1.51 5.698,1.708 0.313,0.198 10 false *1 5.688,0.917 6,1.115 0.313,0.198 10 false *2 5.698,1.51 6.01,1.708 0.313,0.198 10 false *2 3.865,1.99 5.698,2.188 1.833,0.198 10 false from Battery 2.24,2.156 2.854,2.354 0.615,0.198 10 false DOME 0.844,2 1.302,2.198 0.458,0.198 10 false BAT 1.26,0.542 1.417,0.74 0.156,0.198 10 false 3 1.26,1.115 1.417,1.313 0.156,0.198 10 false 2 1.26,1.885 1.417,2.083 0.156,0.198 10 false 5 1.26,3.573 1.417,3.771 0.156,0.198 10 false 4 1.26,4.021 1.417,4.219 0.156,0.198 10 false 1 0.896,3.667 1.354,3.865 0.458,0.198 10 false IG1 0.813,4.125 1.271,4.323 0.458,0.198 10 false ESS 2.115,3.854 3.49,4.052 1.375,0.198 10 false IG1 NO. 2 3.885,2.771 5.281,3.271 1.396,0.5 10 false from Ignition or Starter Switch Assembly*3 3.906,3.677 6.354,3.875 2.448,0.198 10 false from IG1 Relay*4 5.552,4.74 7.115,5.208 1.563,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 2.323,4.354 5.99,4.552 3.667,0.198 10 false *1: except LHD with Continuously Variable Transaxle 2.323,4.667 5.417,4.938 3.094,0.271 10 false *2: for LHD with Continuously Variable Transaxle 2.333,5.021 4.833,5.396 2.5,0.375 10 false *3: w/o Smart Entry and Start System 2.333,5.385 4.74,5.698 2.406,0.313 10 false *4: w/ Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

When U0073, U0124 and/or U0126 is output together with C1432, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073

·

When the speed sensor or the yaw rate and acceleration sensor (airbag ECU assembly) has trouble, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag ECU assembly) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag ECU assembly) first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (BAT TERMINAL)
a.

Turn the ignition switch off.


b.
C375644C14
0.323,1.031 0.74,1.323 0.417,0.292 2.438,1.854 2.167,1.385 true 0.125,0.052 0.438,0.208 0.313,0.156 10 false *a 0.375,1.094 0.99,1.292 0.615,0.198 10 false F147 2.5,1.813 2.958,2.01 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the steering angle sensor connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F147-5 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Turn the ignition switch to ON.


b.
C375644C15
0.323,1.031 0.74,1.323 0.417,0.292 2.24,1.865 1.969,1.396 true 0.125,0.052 0.438,0.208 0.313,0.156 10 false *a 0.375,1.094 0.99,1.292 0.615,0.198 10 false F147 2.302,1.833 2.76,2.031 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Steering Angle Sensor)


Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F147-4 (IG1) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Turn the ignition switch off.


b.
C375644C16
0.323,1.031 0.74,1.323 0.417,0.292 1.635,1.927 1.313,1.406 true 0.125,0.052 0.438,0.208 0.313,0.156 10 false *a 0.375,1.094 0.99,1.292 0.615,0.198 10 false F147 1.688,1.885 2.146,2.083 0.458,0.198 10 false ESS
*a Front view of wire harness connector
(to Steering Angle Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F147-1 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)