Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU assembly is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF indicator light will come on*1, the TRC OFF message will be displayed on the multi-information display*2 and the VSC OFF indicator light will come on.

*1: for Segment Display Type

*2: for TFT Display Type


WIRING DIAGRAM

C349117E08
0.146,2.292 4.125,2.49 3.979,0.198 10 false Combination Meter Assembly 3.188,2.396 5.333,2.594 2.146,0.198 10 false VSC OFF Switch 3.188,2.229 5.333,2.427 2.146,0.198 10 false F155 3.24,1.75 5.385,1.948 2.146,0.198 10 false E 4.073,1.75 6.219,1.948 2.146,0.198 10 false + 4.313,1.75 6.458,1.948 2.146,0.198 10 false 6 3,1.75 5.146,1.948 2.146,0.198 10 false 3 4.927,1.854 5.385,2.052 0.458,0.198 10 false A48 5.25,1.844 5.708,2.042 0.458,0.198 10 false A49 4.969,1.667 5.427,1.865 0.458,0.198 10 false 30 5.292,1.667 5.75,1.865 0.458,0.198 10 false 30 4.969,2.042 5.427,2.24 0.458,0.198 10 false *1 5.292,2.042 5.75,2.24 0.458,0.198 10 false *2 5.479,2.292 7.063,2.833 1.583,0.542 10 false Skid Control ECU (Brake Actuator Assembly) 5.604,1.844 6.063,2.042 0.458,0.198 10 false CSW 0.708,3.427 4.688,3.625 3.979,0.198 10 false : CAN Communication Line 2.604,3.115 6.583,3.313 3.979,0.198 10 false *1: except LHD with Continuously Variable Transaxle 2.615,3.427 6.594,3.625 3.979,0.198 10 false *2: for LHD with Continuously Variable Transaxle

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF SKID CONTROL ECU ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU assembly (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO SKID CONTROL ECU ASSEMBLY CORRECTLY

3.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
Unknown: Unspecified
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

d.

Check that the indicator light and mode condition on the GTS change according to VSC OFF switch (combination switch assembly) operation.

Switch Operation Mode Condition Display TRC OFF Indicator Light*1 Multi-information Display (TRC OFF Message)*2 VSC OFF Indicator Light
Not pressed Normal Does not come on Not displayed Does not come on
Pressing the VSC OFF switch TRC OFF Comes on Displayed Does not come on
Pressing and holding the VSC OFF switch VSC OFF Comes on Displayed Comes on

*1: for Segment Display Type

*2: for TFT Display Type



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

4.PERFORM ACTIVE TEST USING GTS (TRC(TRAC) OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING GTS (TRC(TRAC) OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light TRC OFF indicator light*1
Multi-information display (TRC OFF message)*2
Indicator light ON/OFF*1
Display ON/OFF*2
Can be observed on the combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Can be observed on the combination meter assembly

*1: for Segment Display Type

*2: for TFT Display Type


Chassis > ABS/VSC/TRC > Active Test
Tester Display
TRC(TRAC) OFF Indicator Light
50004 105 78
Chassis > ABS/VSC/TRC > Active Test
Tester Display
VSC OFF Indicator Light
50004 105 79

b.

Check the TRC OFF indicator light*1, multi-information display (TRC OFF message)*2 and VSC OFF indicator light on the combination meter assembly turn ON or OFF in accordance with the GTS operation.

OK:

The TRC OFF indicator light*1, multi-information display (TRC OFF message)*2 and VSC OFF indicator light turn ON or OFF in accordance with the GTS operation.


*1: for Segment Display Type

*2: for TFT Display Type



Result:
Result Proceed to
OK A
NG (for Segment Display Type) B
NG (for TFT Display Type) C



A

5.INSPECT VSC OFF SWITCH

B

7.CHECK COMBINATION METER ASSEMBLY

C

8.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT VSC OFF SWITCH
a.

Turn the ignition switch off.



c.

Inspect the VSC OFF switch.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION

OK:

The VSC OFF switch operates normally.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Disconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A48-30 (CSW) - F155-6 (+) Always Below 1 Ω
A48-30 (CSW) or F155-6 (+) - Body ground Always 10 kΩ or higher
F155-3 (E) - Body ground Always Below 1 Ω

for LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A49-30 (CSW) - F155-6 (+) Always Below 1 Ω
A49-30 (CSW) or F155-6 (+) - Body ground Always 10 kΩ or higher
F155-3 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform an Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
VSC TRC Indicator
50004 122 102
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94

c.

Check the combination meter assembly.

OK:

The TRC OFF indicator light and VSC OFF indicator light turn on or off in accordance with GTS operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

8.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform the Active Test of the combination meter assembly (meter CPU) using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94

c.

Check the combination meter assembly.

OK:

The multi-information display and VSC OFF indicator light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

NG