Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE FLUID › from 2018.01
RM30M0E _52 Drivetrain _052750 K411 CVT _0259914 CONTINUOUSLY VARIABLE TRANSAXLE FLUID N

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE FLUID  ADJUSTMENT  


PROCEDURE

Hide 1. PRECAUTIONS AND WORK DESCRIPTION

a.

The K411 continuously variable transaxle assembly does not have an oil filler tube or oil level dipstick. When adding fluid, add fluid through the refill hole in the transaxle case. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the transaxle oil pan sub-assembly.

HINT:

"Overflow" indicates the condition under which fluid comes out of the overflow plug hole.



b.

When adding fluid, add the specified amount of fluid while the engine assembly is cold. Then, warm up the engine assembly to circulate the fluid in the continuously variable transaxle assembly and adjust the fluid level with the engine idling at the specified fluid temperature.


c.

The K411 continuously variable transaxle assembly requires Toyota Genuine CVT fluid FE.


d.

When adjusting the fluid level, park the vehicle on level ground (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).


e.

When adjusting the fluid level, turn off all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, to reduce load.


f.

The fluid temperature shown in the text is "A/T Oil Temperature 1" displayed on the GTS.


g.

Fluid level adjustment should be performed according to the following procedure and notes.

C202513E09
1.875,2.333 2.719,2.594 2.719,2.594 2.719,2.708 false 5.625,2.385 6.135,2.656 6.135,2.656 6.135,2.813 false 1.552,3.396 4.271,3.76 2.719,0.365 12 false 3. ADJUST FLUID TEMPERATURE 0.302,5.781 2.25,6.125 1.948,0.344 12 false 4. ADJUST FLUID LEVEL 0.063,0 2.146,0.344 2.083,0.344 12 false Fluid Filling Procedure: 0.063,0.344 2.313,1.073 2.25,0.729 12 false 1. PERFORM INITIAL FILLING (when necessary) 4.021,0.344 7.083,0.75 3.063,0.406 12 false 2. ADD SPECIFIED AMOUNT OF FLUID 0.052,1.083 2.01,1.448 1.958,0.365 10 false Add fluid to the specified level. 4.208,0.792 6.906,1.5 2.698,0.708 10 false Add the correct amount of fluid specified for the operation that was performed. 0.219,2.552 1.354,3.563 1.135,1.01 10 false Add fluid until fluid comes out of the overflow plug hole. 0.146,7.708 1.927,8.708 1.781,1 10 false Keep the overflow plug open until the fluid flow slows and only drops come out. 0.302,6.188 2.688,6.885 2.385,0.698 10 false Drain excess fluid at the specified fluid temperature. 4.281,6.073 6.708,6.719 2.427,0.646 10 false If no fluid comes out, add fluid until fluid comes out of the overflow plug hole. 1.542,3.813 6.885,4.552 5.344,0.74 10 false Start the engine to circulate the fluid. Enter fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified level. 6.365,1.771 7.042,2.76 0.677,0.99 10 false Specified Amount of Fluid 2.094,2.698 3.333,3.302 1.24,0.604 10 false No. 1 Transmission Oil Filler Tube 5.729,2.823 6.625,3.208 0.896,0.385 10 false Overflow Plug


Hide 2. WORK FLOW

a.

The adjustment should be performed according to the procedure referenced in the work flow below.

C381197E02
2.677,0.625 4.885,0.802 2.208,0.177 10 false [STEP 4] Perform Initial Filling 3.906,0.979 6.667,1.167 2.76,0.188 10 false Operations that do not require initial filling: 0.323,1.26 3.292,1.438 2.969,0.177 8 false Changing the continuously variable transaxle assembly. 0.333,1.49 3.333,1.74 3,0.25 8 false Removal and installation of the torque converter assembly. 0.333,1.719 3.667,1.969 3.333,0.25 8 false Removal and installation of the transaxle oil pan sub-assembly. 0.344,1.969 3.677,2.219 3.333,0.25 8 false Removal and installation of the front drive shaft assembly. 0.333,2.219 3.667,2.469 3.333,0.25 8 false Changing the CVT type T oil seal. 0.344,2.438 3.677,2.688 3.333,0.25 8 false Removal and installation of the transmission oil cooler. 0.344,2.667 3.677,2.917 3.333,0.25 8 false Fluid drain and refill. 0.229,0.979 2.5,1.229 2.271,0.25 10 false Operations that require initial filling: 4.01,1.219 6.979,1.396 2.969,0.177 8 false Repair of a fluid leak, etc. 2.479,3.083 4.927,3.313 2.448,0.229 10 false [STEP 5] Add Specified Amount of Fluid 2.583,3.667 4.781,3.896 2.198,0.229 10 false [STEP 6] Adjust Fluid Temperature 1.302,4.146 5.854,4.333 4.552,0.188 10 false Enter fluid temperature detection mode and engine idle speed control mode 2.813,4.708 4.417,4.885 1.604,0.177 10 false Idling (Warm up the fluid) 5.906,4.708 6.958,5.594 1.052,0.885 10 false Stop the engine and wait until the fluid temperature drops 3.135,5.24 4.073,6.125 0.938,0.885 10 false Check the fluid temperature 2.531,6.104 4.635,6.313 2.104,0.208 10 false Fluid level adjustment temperature 2.667,6.688 5.104,6.854 2.438,0.167 10 false [STEP 7] Adjust Fluid Level 3.021,7.083 4.198,7.26 1.177,0.177 10 false Drain excess fluid 2.833,7.646 4.438,7.823 1.604,0.177 10 false Check the amount of fluid 0.354,7.635 0.938,7.792 0.583,0.156 10 false Add fluid 6.385,7.635 6.969,7.813 0.583,0.177 10 false Overflow 4.875,7.823 6.042,8.073 1.167,0.25 10 false Fluid comes out 1.26,7.823 2.5,8.083 1.24,0.26 10 false No fluid comes out 1.99,8.333 5.667,8.542 3.677,0.208 10 false [STEP 8] Perform ATF Thermal Degradation Estimate Reset 2.781,8.927 4.5,9.125 1.719,0.198 10 false [STEP 9] Rebuild Work 3.479,9.51 3.885,9.677 0.406,0.167 10 false END 3.375,0.083 3.833,0.292 0.458,0.208 10 false START 0.083,0.063 2.292,0.24 2.208,0.177 10 false WORK FLOW: 4.219,5.427 5.646,5.844 1.427,0.417 10 false Above fluid level adjust ment temperature 1.5,5.427 2.875,5.844 1.375,0.417 10 false Below fluid level adjust ment temperature


Hide 3. PREPARATION WORK

NOTICE:

If the continuously variable transaxle assembly is hot (fluid temperature is high), wait until the fluid temperature becomes the same as the ambient temperature before starting the following procedure (recommended fluid temperature: approximately 20°C [68°F]).


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.

Remove the engine under cover LH (w/o Metal type under cover).

Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>REMOVAL


c.

Remove the center engine under cover (w/ Metal type under cover).

Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>REMOVAL


d.

Remove the No. 1 engine under cover sub-assembly (w/ Metal type under cover).

Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>REMOVAL


Hide 4. PERFORM INITIAL FILLING

NOTICE:

After performing either of the following operations, it is not necessary to perform the initial filling procedure. Proceed to Add Specified Amount of Fluid (Step 5).


Operations that do not Require Initial Filling
Repair of a fluid leak, etc.

a.
C219035

Remove the refill plug and gasket from the continuously variable transaxle assembly.


b.
C219032

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the continuously variable transaxle assembly.

NOTICE:
·

If fluid comes out after removing the overflow plug, wait until the fluid flow slows and only drops come out.

·

If fluid comes out, it is not necessary to perform the initial filling procedure. After checking the tightening torque of the No. 1 transmission oil filler tube, temporarily install the overflow plug.




c.
C288106

Using a 6 mm hexagon socket wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)

NOTICE:

If the No. 1 transmission oil filler tube is not tightened to the specified torque, the amount of fluid cannot be precisely adjusted.


HINT:

To check the torque of the No. 1 transmission oil filler tube, insert the hexagon socket into the overflow plug hole.



d.

Perform initial filling.

i.
C219037

Add fluid to the refill hole until it flows out of the overflow plug hole.

NOTICE:

Use Toyota Genuine CVT fluid FE.




e.
C219034

Wait until the fluid flow slows and only drips come out.


f.
C219032

Temporarily install the gasket and overflow plug to the continuously variable transaxle assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



g.
C219035

Temporarily install the gasket and refill plug to the continuously variable transaxle assembly.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



Hide 5.ADD SPECIFIED AMOUNT OF FLUID

a.
C219035

Remove the refill plug and gasket from the continuously variable transaxle assembly.


b.
C219036

Add fluid to the refill hole using the correct amount of fluid as listed in the table below.

NOTICE:

The refill amount differs depending on the operation that was performed.


Standard Capacity:
Operation Performed Fill Amount
Changing the continuously variable transaxle assembly (A new torque converter assembly has been installed). 3.4 liters (3.6 US qts, 3.0 Imp. qts)
Changing the continuously variable transaxle assembly (The old torque converter assembly has been reused). 2.7 liters (2.9 US qts, 2.4 Imp. qts.)
Removal and installation of the torque converter assembly.
Removal and installation of the transaxle oil pan sub-assembly. 2.6 liters (2.7 US qts, 2.3 Imp. qts)
Removal and installation of the front drive shaft assembly.
Changing the CVT type T oil seal.
Removal and installation of the transmission oil cooler.
Fluid drain and refill.
Repair of a fluid leak, etc. 0.4 liters (0.4 US qts, 0.4 Imp. qts)



c.
C219035

Temporarily install the gasket and refill plug to avoid fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



d.

Lower the vehicle.


Hide 6.ADJUST FLUID TEMPERATURE

a.

When using the GTS:

i.

Connect the GTS to the DLC3 with the ignition switch off.


ii.

Turn the ignition switch to ON and turn the GTS on.


iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

iv.

Select the Data List item: A/T Oil Temperature 1.


v.

According to the display on the GTS, perform the Active Test "Connect the TC and TE1 / ON".

HINT:

The indicator lights on the combination meter blink to indicate that a DTC has been stored when the Active Test "Connect the TC and TE1 / ON" is performed.




b.

When not using the GTS:

i.
C166029C73
1.333,1.927 1.771,1.479 true 1.583,0.896 2.021,0.448 true 1.125,1.844 1.365,2.021 0.24,0.177 10 false TC 2.063,0.344 2.427,0.521 0.365,0.177 10 false CG 0.125,0.073 0.344,0.25 0.219,0.177 10 false *1
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.

SST
09843-18040  



c.

Depress and hold the brake pedal.


d.

Start the engine.

NOTICE:

Make sure that all electrical systems, such as the air conditioning, lighting system and audio system, are off.



e.

Slowly move the shift lever from P to D, and then back to P (keep the shift lever in each position for approximately 3 seconds).

HINT:

Slowly move the shift lever to circulate the fluid through each part of the continuously variable transaxle assembly.



f.
C381214C05
0.365,2.51 0.5,2.708 0.135,0.198 10 false P 0.365,2.906 0.5,3.104 0.135,0.198 10 false N 0.365,3.156 0.5,3.354 0.135,0.198 10 false D 0.083,2.823 0.271,3.021 0.188,0.198 10 false *a 0.094,3.917 0.281,4.115 0.188,0.198 10 false *b 1.375,2.5 1.563,2.698 0.188,0.198 10 false *f 1.365,3.417 1.552,3.615 0.188,0.198 10 false *d 2.375,3.417 2.563,3.615 0.188,0.198 10 false *e 2.531,4.281 2.719,4.479 0.188,0.198 10 false *c 0.583,3.927 0.771,4.125 0.188,0.198 10 false P 0.792,3.927 0.979,4.125 0.188,0.198 10 false D 0.99,3.927 1.177,4.125 0.188,0.198 10 false N 1.188,3.927 1.375,4.125 0.188,0.198 10 false D 1.385,3.927 1.573,4.125 0.188,0.198 10 false N 1.594,3.927 1.781,4.125 0.188,0.198 10 false D 1.792,3.927 1.979,4.125 0.188,0.198 10 false N 1.99,3.927 2.177,4.125 0.188,0.198 10 false D 2.208,3.927 2.396,4.125 0.188,0.198 10 false D 2.396,3.927 2.583,4.125 0.188,0.198 10 false D 2.604,3.927 2.792,4.125 0.188,0.198 10 false D
*a Shift Position
*b Indication of Shift Position
*c Fluid Temperature Detection Mode
*d 6 sec. or more
*e 2 sec.
*f Less than 1.5 sec.


While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter fluid temperature detection mode.



g.

Move the shift lever to P.


h.

Release the brake pedal.


i.

Disconnect the terminals of the DLC3.

i.

When using the GTS:

·

According to the display on the GTS, perform the Active Test "Connect the TC and TE1 / OFF".



ii.

When not using the GTS:

·

Remove SST from terminals 13 (TC) and 4 (CG).


NOTICE:

Make sure that terminals 13 (TC) and 4 (CG) are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting the terminals activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature reaches the specified value and the engine speed is maintained.

·

Even after the terminals are disconnected, fluid temperature detection mode remains active until the ignition switch is turned off.





j.

Adjust the fluid temperature to the fluid level adjustment temperature.

i.

Check the fluid temperature by monitoring the D shift indicator.

HINT:
·

In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.

·

The fluid filling procedure should be performed when the D shift indicator is on (the fluid temperature is within the fluid level adjustment temperature range).




ii.

Adjust the fluid temperature.

·

If the D shift indicator is off [Below Fluid Level Adjustment Temperature: 35°C (95°F) or less]: Warm up the engine with the engine idling in engine idle speed control mode until the D shift indicator turns on.


·

If the D shift indicator is on [Fluid Level Adjustment Temperature: 35 to 45°C (95 to 113°F)]: Immediately proceed to Adjust Fluid Level (Step 7).


·

If the D shift indicator is blinking [Above Fluid Level Adjustment Temperature: 45°C (113°F) or more]: Stop the engine and wait until the fluid temperature drops to 35°C (95°F) or less (the D shift indicator goes off). Then perform the adjust fluid temperature procedure again from the beginning.


Relationship between Fluid Level Adjustment Temperature and the D Shift Indicator:
Below Fluid Level Adjustment Temperature Fluid Level Adjustment Temperature Above Fluid Level Adjustment Temperature
Fluid Temperature ("A/T Oil Temperature 1" displayed on the GTS) 35°C (95°F) or less 35 to 45°C (95 to 113°F) 45°C (113°F) or more
D Shift Indicator Off On Blinks




Hide 7.ADJUST FLUID LEVEL

CAUTION:

Use caution while the engine assembly is idling and the radiator fan is operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.
C219032

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the continuously variable transaxle assembly.

CAUTION:

Be careful as the fluid coming out of the overflow plug hole is hot.



c.

Check the amount of fluid that comes out of the overflow plug hole.

·

If the amount of fluid that comes out of the overflow plug hole is large, proceed to *1.

·

If no fluid comes out of the overflow plug hole, proceed to *2.


NOTICE:

If only a small amount of fluid (approximately 5 cc) comes out of the overflow plug hole, then only fluid remaining in the No. 1 transmission oil filler tube has come out. This is not considered to be overflow.



d.
C219037

*2:

If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add fluid through the refill hole until fluid comes out of the overflow plug hole. Wait until the fluid flow slows and only drips come out.

NOTICE:

Use Toyota Genuine CVT fluid FE.



e.
C219034

*1:

If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drips come out.

HINT:

The fluid flow will not stop completely because the fluid continues to expand as its temperature increases.



f.
C219032

Install a new gasket and overflow plug to the continuously variable transaxle assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


g.
C219035

Install a new gasket and refill plug to the continuously variable transaxle assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


h.

Lower the vehicle.


i.

Turn the ignition switch off.

HINT:

Turning the ignition switch off exits fluid temperature detection mode.



j.

Remove the GTS from the DLC3 (when using the GTS).


Hide 8.PERFORM ATF THERMAL DEGRADATION ESTIMATE RESET

NOTICE:

If approximately 50% or more of the CVT fluid has been replaced during a repair of the transaxle or a similar operation, perform ATF Thermal Degradation Estimate Reset.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Hide 9. REBUILD WORK

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for fluid leaks.


d.

Install the No. 1 engine under cover sub-assembly (w/ Metal type under cover).

Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>INSTALLATION


e.

Install the center engine under cover (w/ Metal type under cover).

Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>INSTALLATION


f.

Install the engine under cover LH (w/o Metal type under cover).

Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>INSTALLATION


g.

Lower the vehicle.