The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCHARGE FUEL SYSTEM PRESSURE
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
4.REMOVE FRONT WHEELS
51442C
5.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)
51441C
6.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)
51451A
7.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)
51405A
8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
9.DRAIN ENGINE OIL
10.DRAIN ENGINE COOLANT
11.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID
Click hereDrivetrain>K411 CVT>OIL PAN>REMOVAL
12611
12.REMOVE NO. 1 ENGINE COVER
23826
13.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
Slide the hose clip and disconnect the No. 1 fuel vapor feed hose from the purge VSV (purge valve).
23827A
14.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE
Disconnect the No. 2 fuel vapor feed hose from the purge VSV (purge valve).
17341T
15.DISCONNECT NO. 1 AIR HOSE
12262
16.DISCONNECT NO. 2 VENTILATION HOSE
17880
17.REMOVE AIR CLEANER HOSE ASSEMBLY
18.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
Disconnect the mass air flow meter connector.
Disengage the 2 clamps to separate the engine wire from the air cleaner cap sub-assembly.
Disengage the 2 clamps of the air cleaner cap sub-assembly.
Disengage the 2 guides to remove the air cleaner cap sub-assembly from the air cleaner case sub-assembly.
17801
19.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
17701
20.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Disengage the clamp to separate the engine wire from the air cleaner case sub-assembly.
Remove the 3 bolts and air cleaner case sub-assembly from the air cleaner bracket.
28800
21.REMOVE BATTERY
Remove the terminal cover from the positive (+) battery terminal.
| *1 | Engine Room Main Wire |
| *2 | Engine Wire |
Remove the nut to disconnect the engine room main wire with engine wire from the positive (+) battery terminal.
Disengage the 2 claws to disconnect the engine room main wire from the engine wire.
Remove the 2 nuts, battery clamp bolt and battery clamp sub-assembly from the battery carrier assembly.
Remove the battery from the battery tray.
74431
22.REMOVE BATTERY TRAY
Remove the battery tray from the battery carrier assembly.
74410
23.REMOVE BATTERY CARRIER ASSEMBLY
Disengage the 4 clamps to disconnect the wire harness from the battery carrier assembly.
Remove the 5 bolts and battery carrier assembly from the engine mounting insulator LH and vehicle.
16361A
24.REMOVE FAN AND GENERATOR V BELT
15301
25.REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY
11452
26.REMOVE OIL LEVEL DIPSTICK GUIDE
17167
27.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
82121
28.DISCONNECT ENGINE WIRE
29.REMOVE WIRE HARNESS CLAMP BRACKET
27020
30.REMOVE GENERATOR WITH REGULATOR ASSEMBLY
44774
31.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Slide the hose clip and disconnect the union to connector tube hose from the intake manifold.
25860D
32.SEPARATE VACUUM SWITCHING VALVE ASSEMBLY
Disconnect the vacuum switching valve assembly connector.
Remove the bolt and separate the vacuum switching valve assembly from the intake manifold.
17341T
33.DISCONNECT NO. 1 AIR HOSE
Disengage the clamp to disconnect the No. 1 air hose from the intake manifold.
35141F
34.DISCONNECT NO. 1 BREATHER PLUG
Disengage the clamp to disconnect the No. 1 breather plug from the hose clamp.
16571C
35.DISCONNECT NO. 1 RADIATOR HOSE
Slide the hose clip and disconnect the No. 1 radiator hose from the cylinder head sub-assembly.
16572D
36.DISCONNECT NO. 2 RADIATOR HOSE
Slide the hose clip and disconnect the No. 2 radiator hose from the water inlet.
87246
37.DISCONNECT OUTLET HEATER WATER HOSE
Slide the hose clip and disconnect the outlet heater water hose from the heater radiator assembly.
87245
38.DISCONNECT INLET HEATER WATER HOSE
Slide the hose clip and disconnect the inlet heater water hose from the heater radiator assembly.
23841B
39.REMOVE EFI FUEL PIPE CLAMP
23901
40.DISCONNECT FUEL TUBE SUB-ASSEMBLY
88320
41.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/ Cooler System)
Disconnect the cooler compressor assembly connector.
Remove the 4 bolts and separate the cooler compressor assembly from the cylinder block sub-assembly and oil pan sub-assembly.
Separate the cooler compressor assembly together with the discharge hose and suction hose, then suspend them from the vehicle with a piece of rope.
55550
42.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
82121
43.DISCONNECT ENGINE WIRE (for LHD)
Remove the relay block cover from the engine room relay block.
Remove the bolt to disconnect the engine wire from the vehicle.
Disengage the clamp to disconnect the engine wire from the vehicle.
Disconnect the connector from the engine room relay block.
Remove the nut from the engine room relay block.
Disengage the 2 claws to disconnect the engine wire from the engine room relay block.
Disconnect the 4 connectors.
Disengage the 2 clamps to disconnect the engine wire from the wire harness clamp bracket and vehicle.
Disengage the clamp to disconnect the engine wire from the wire harness clamp bracket.
Disengage the grommet and pass the engine wire through the hole to the inside of the engine room.
82121
44.DISCONNECT ENGINE WIRE (for RHD)
Remove the relay block cover from the engine room relay block.
Remove the bolt to disconnect the engine wire from the vehicle.
Disengage the clamp to disconnect the engine wire from the vehicle.
Disconnect the connector from the engine room relay block.
Remove the nut from the engine room relay block.
Disengage the 2 claws to disconnect the engine wire from the engine room relay block.
Disconnect the 3 connectors.
Disengage the 2 clamps to disconnect the engine wire from the wire harness clamp bracket and vehicle.
Disengage the grommet and pass the engine wire through the hole to the inside of the engine room.
57533B
45.REMOVE FRONT FLOOR CENTER BRACE
17410
46.REMOVE FRONT EXHAUST PIPE ASSEMBLY
33820B
47.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
48.REMOVE FRONT DRIVE SHAFT ASSEMBLY
45259A
49.REMOVE COLUMN HOLE COVER SILENCER SHEET
45209
50.DISCONNECT STEERING SLIDING YOKE SUB-ASSEMBLY
45025D
51.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
43498A
52.REMOVE NO. 1 DRIVE SHAFT HEAT INSULATOR
Remove the 2 bolts and No. 1 drive shaft heat insulator from the oil pan sub-assembly.
12137
53.REMOVE OIL PAN PROTECTOR (w/ Metal Type Under Cover)
Remove the 3 bolts and oil pan protector from the oil pan sub-assembly.
12144
54.REMOVE OIL PAN COVER SILENCER (w/ Metal Type Under Cover)
Perform this procedure only when replacement of the oil pan cover silencer is necessary.
Remove the oil pan cover silencer from the oil pan protector.
55.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the bolt and wire harness clamp bracket from the continuously variable transaxle assembly.
56.REMOVE ENGINE ASSEMBLY WITH CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
Loosen the engine moving control rod bolt.
|
Attachment Placement Positions |
Place the height adjustment or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with continuously variable transaxle assembly and front suspension crossmember sub-assembly.
Place the height adjustment and plate lift attachments so that the engine assembly with continuously variable transaxle assembly is level.
Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
As the engine assembly with continuously variable transaxle assembly is very heavy, be sure to support it securely.
To prevent deformation of the continuously variable transaxle oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the continuously variable transaxle assembly.
Remove the bolt and 2 nuts to disconnect the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the through bolt and nut to disconnect the engine mounting insulator LH from the engine mounting bracket LH.
Loosen by holding the nut and turning the bolt.
Remove the 6 bolts and engine assembly with continuously variable transaxle assembly with front suspension crossmember sub-assembly from the vehicle.
When removing the engine assembly with continuously variable transaxle assembly and front suspension crossmember sub-assembly, be careful not to damage any wire harnesses or the steering shaft.
28100
57.REMOVE STARTER ASSEMBLY
11363A
58.REMOVE FLYWHEEL HOUSING SIDE COVER
32101G
59.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
60.INSTALL ENGINE HANGER
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the No. 1 engine hanger and No. 2 engine hanger to the cylinder head sub-assembly with the 2 bolts.
| Part Name | Part No. |
|---|---|
| No. 1 engine hanger | 12281-0Y070 |
| No. 2 engine hanger | 12282-0Y060 |
| Bolt | 90105-T0125 |
51201
61.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Using an engine sling device and a chain block, suspend the engine assembly with continuously variable transaxle assembly.
Remove the through bolt and front suspension crossmember from the No. 2 engine moving control rod.
82121
62.REMOVE ENGINE WIRE
Remove the 2 bolts to disconnect the engine wire from the cylinder head sub-assembly.
Remove the 2 nuts to disconnect the engine wire from the cylinder head cover sub-assembly.
Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.
Disconnect all the engine wire connectors.
Make sure that no engine wires are connected to the engine.
16260
63.DISCONNECT WATER BY-PASS HOSE ASSEMBLY
Slide the hose clip and disconnect the water by-pass hose assembly from the No. 1 water by-pass pipe sub-assembly.
87245
64.REMOVE INLET HEATER WATER HOSE
Disengage the clamp to disconnect the hose clamp from the wire harness clamp bracket.
Slide the hose clip to separate the inlet heater water hose from the cylinder head sub-assembly.
65.FIX ENGINE ASSEMBLY
Attach the sling device to the engine hangers and chain block.
Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.
|
Attachment Placement Position |
To enable removal of the continuously variable transaxle assembly, adjust the positions of the height adjustment and plate lift attachments and set them in place.
Place the height adjustment and plate lift attachments so that the engine assembly with continuously variable transaxle assembly is level.
As the engine assembly with continuously variable transaxle assembly is very heavy, be sure to support it securely.
To prevent deformation of the continuously variable transaxle oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the continuously variable transaxle assembly.
Use a belt with a tightening mechanism or a rope to secure the engine assembly to the engine lifter.
Do not tighten the belt with a tightening mechanism or the rope any more than is necessary.
30400
66.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
Remove the 8 bolts and continuously variable transaxle assembly from the engine assembly.
To prevent damage to the knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.
Do not allow the torque converter assembly to fall off.
Bolt A: Remove from continuously variable transaxle assembly side
Bolt B: Remove from engine assembly side
32101B
67.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
Using height adjustable attachments and plate lift attachments, place the engine assembly on a flat, level surface.
Using height adjustable attachments and plate lift attachments, place the engine assembly horizontally.
Using an engine sling device and engine lift, secure the engine assembly before servicing.
Using SST, hold the crankshaft pulley.
Remove the 8 bolts, the rear drive plate spacer, the drive plate and ring gear sub-assembly and the front drive plate spacer from the crankshaft.
68.INSTALL ENGINE STAND
Using a sling device and chain block, install the engine assembly to the engine stand.
Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.
Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.
12305
69.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the 3 bolts.
Disengage the hook and remove the engine mounting insulator sub-assembly RH from the vehicle.
12372A
70.REMOVE ENGINE MOUNTING INSULATOR LH
Only perform this procedure when replacement of the engine mounting insulator LH is necessary.
Remove the 5 bolts.
Disengage the hook and remove the engine mounting insulator LH from the vehicle.