The steering lock actuator activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little in the same manner as is done for a vehicle with a mechanical key to change the position of the lock hole.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Unable to lock steering wheel |
|
- |
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Perform either of the following operations to lock/unlock the steering:
To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.
To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.
*: for CVT
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).
After performing repairs, confirm that the problem does not recur.
When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Lock Request Receive | Reception state of steering lock request signal by certification ECU (smart key ECU assembly)
|
OK or NG | OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*
NG: Except above |
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
*: for CVT
| Tester Display |
|---|
| Lock Request Receive |
The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door with the shift lever in P (for CVT), and OK is displayed on the GTS screen.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
The steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the steering lock ECU (steering lock actuator assembly) connector.
| *a | Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly)) |
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-1 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, check for looseness in the ground cable connection.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-7 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-1 (GND) - Body ground | Always | Below 1 Ω |
Reconnect the steering lock ECU (steering lock actuator assembly) connector.
Move the shift lever to P* and turn the engine switch off.
*: for CVT
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | F15-3 (IGE) - F15-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor not operating → Operating → Not operating |
When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
In order to take measurements when the lock motor is operating, perform either of the following operations:
To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.
To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.
*: for CVT
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F15 steering lock ECU (steering lock actuator assembly) connector.
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Check for deformation and corrosion of the connector case and terminals.
There is no deformation or corrosion of the connector case or terminals.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-3 (IGE) - F43-17 (SLR+) | Always | Below 1 Ω |
| F15-3 (IGE) - Body ground | Always | 10 kΩ or higher |
| F43-17 (SLR+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the steering lock ECU (steering lock actuator assembly) connector.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-3 (IGE) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the steering lock ECU (steering lock actuator assembly) with a new one.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY
Perform registration.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front door courtesy light switch assembly LH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly LH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
Front door courtesy light switch assembly LH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F31 front door courtesy light switch assembly LH connector.
Disconnect the 6M driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-1 - 6M-2 | Always | Below 1 Ω |
| F31-1 - Body ground | Always | 10 kΩ or higher |
| 6M-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
Front door courtesy light switch assembly RH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F32 front door courtesy light switch assembly RH connector.
Disconnect the 6M driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F32-1 - 6M-2 | Always | Below 1 Ω |
| F32-1 - Body ground | Always | 10 kΩ or higher |
| 6M-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6M-2 - MB-18 (DCTY) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the body computer with a new one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
The engine switch is off.
The shift lever is in P*1.
A door is opened or a door lock operation (door lock, wireless door lock or key-linked lock operation*2) is performed.
*1: for CVT
*2: This is the lock/unlock operation with the mechanical key.
Turn the steering wheel and check the steering condition.
Steering is locked.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Manual Transaxle) | B |
| NG (for CVT) | C |
A
B
C
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift P Signal | Shift position (P) signal | OK or NG | ON: Shift lever in P
OFF: Shift lever not in P |
·
Use this item to determine if the shift position switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". |
ON (shift lever in P) or OFF (shift lever not in P) appears on the screen according to the shift lever position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
The engine switch is off.
The shift lever is in P*1.
A door is opened or a door lock operation (door lock, wireless door lock or key-linked lock operation*2) is performed.
*1: for CVT
*2: This is the lock/unlock operation with the mechanical key.
Turn the steering wheel and check the steering condition.
Steering is locked.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Lock | State of whether steering lock ECU
(steering lock actuator assembly) has determined steering is locked |
Set or Unset | Set: Steering locked
Unset: Steering unlocked |
If this item displays "Unset", the steering does not lock. |
| Steering Unlock | State of whether steering lock ECU
(steering lock actuator assembly) determined steering is unlocked |
Set or Unset | Set: Steering unlocked
Unset: Steering locked |
If this item displays "Unset", the steering does not unlock (engine cannot be started). |
"Steering Lock" is "Set" and "Steering Unlock" is "Unset"
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
Perform registration.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Lock Request Receive | Reception state of steering lock request signal by certification ECU (smart key ECU assembly)
|
OK or NG | OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*
NG: Except above |
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
*: for CVT
| Tester Display |
|---|
| Lock Request Receive |
The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door with the shift lever in P (for CVT), and OK is displayed on the GTS screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F20 shift lock control ECU (shift lock control unit assembly) connector.
| *a | Component without harness connected
(Shift Lock Control ECU (Shift Lock Control Unit Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (P2) - 7 (E) | Shift lever in P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F20 shift lock control ECU (shift lock control unit assembly) connector.
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F20-2 (P2) - F43-8 (P) | Always | Below 1 Ω |
| F20-7 (E) - Body ground | Always | Below 1 Ω |
| F20-2 (P2) - Body ground | Always | 10 kΩ or higher |
| F43-8 (P) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG