Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0090108 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1524  Motor Terminal Voltage  C1555  Motor Relay Welding Failure  


DESCRIPTION

The power steering ECU assembly supplies current to the power steering motor assembly through the motor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1524 Motor Terminal Voltage Short (or open) in motor circuit or abnormal voltage in motor circuit
·

Power steering motor assembly

·

Power steering ECU assembly


EPS warning light: Comes on Ignition switch ON again -
C1555 Motor Relay Welding Failure Predriver (Motor relay circuit) malfunction
·

Power steering motor assembly

·

Power steering ECU assembly


EPS warning light: Comes on Ignition switch ON again -

WIRING DIAGRAM

C378864E03
1.781,2.563 4.063,2.833 2.281,0.271 10 false Power Steering Motor Assembly 4.406,2.563 5.729,2.979 1.323,0.417 10 false Power Steering ECU Assembly 4.156,1.219 4.469,1.417 0.313,0.198 10 false z9 4.156,2.01 4.469,2.208 0.313,0.198 10 false z9 4.177,1 4.49,1.198 0.313,0.198 10 false 1 4.188,1.792 4.5,1.99 0.313,0.198 10 false 2 4.49,1.219 4.802,1.417 0.313,0.198 10 false M1 4.479,2.01 4.792,2.208 0.313,0.198 10 false M2

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.CHECK POWER STEERING ECU ASSEMBLY
a.

Start the engine.


b.
C228663C30
1.385,0.667 1.885,0.917 0.5,0.25 2.083,2.583 1.802,1.708 true 1.167,2.583 1.458,1.698 true 0.083,0.083 0.333,0.333 0.25,0.25 10 false *a 1.563,0.708 1.875,0.906 0.313,0.198 10 false z9 1.021,2.635 1.333,2.833 0.313,0.198 10 false M2 2.01,2.635 2.323,2.833 0.313,0.198 10 false M1
*a Component with harness connected
(Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z9-1 (M1) - Body ground Engine running and steering wheel being turned to left 6 to 11 V
z9-1 (M1) - Body ground Engine running and steering wheel being turned to right 11 to 14 V
z9-2 (M2) - Body ground Engine running and steering wheel being turned to left 11 to 14 V
z9-2 (M2) - Body ground Engine running and steering wheel being turned to right 6 to 11 V



Result:
Proceed to
OK
NG



OK

2.INSPECT POWER STEERING MOTOR ASSEMBLY

NG

REPLACE POWER STEERING ECU ASSEMBLY

2.INSPECT POWER STEERING MOTOR ASSEMBLY
a.

Disconnect the power steering ECU assembly connector.


b.
C349136C05
1.469,0.281 1.969,0.531 0.5,0.25 1.167,1.667 1.5,1.198 true 2.25,1.667 1.938,1.208 true 0.083,0.083 0.333,0.333 0.25,0.25 10 false *a 1.646,0.323 1.958,0.521 0.313,0.198 10 false z9 1.021,1.719 1.333,1.917 0.313,0.198 10 false M1 2.25,1.719 2.563,1.917 0.313,0.198 10 false M2
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-1 (M1) - z9-2 (M2) Always 0.1 to 1.0 Ω
z9-1 (M1) or z9-2 (M2) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE POWER STEERING MOTOR ASSEMBLY