Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › from 2018.01
RM30M0E _55 Steering _017104 STEERING COLUMN _0090116 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45130 2.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 3.REMOVE STEERING WHEEL ASSEMBLY

Hide 55106 4.REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for LHD)

Hide 55106 5.REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for RHD)

Hide 45289A 6.REMOVE STEERING COLUMN COVER SUPPORT (w/ Smart Entry and Start System)

a.
C380906

Disengage the 4 claws and remove the steering column cover support.


Hide 45287 7.REMOVE LOWER STEERING COLUMN COVER

a.
C382969

Remove the 3 screws.


b.

Release the tilt lever, disengage the 3 claws and remove the lower steering column cover.


Hide 45286B 8.REMOVE UPPER STEERING COLUMN COVER

a.
C380908

Disengage the claw and remove the upper steering column cover.


Hide 9.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.

Disconnect all the connectors from the combination switch assembly with spiral cable sub-assembly.


b.
C382970C01
0.813,0.594 1.052,0.229 true 0.667,0.573 0.479,0.219 true 1.073,0.146 1.281,0.333 0.208,0.188 10 true *1 0.302,0.125 0.51,0.313 0.208,0.188 10 true *a
*1 Clamp
*a Claw


Use pliers to hold the clamp and raise the claw with a screwdriver. Remove the combination switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 45259A 10.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.

Fold back the floor carpet.


b.
C382971

Remove the 2 clips and the column hole cover silencer sheet.


Hide 45209 11.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C382972C01
1.75,1.333 2.031,1.208 2.031,1.208 1.729,1.25 true 2.042,1.104 2.229,1.323 0.188,0.219 10 false *a 1.031,0.74 1.188,0.938 0.156,0.198 10 false A 1.25,1.438 1.406,1.635 0.156,0.198 10 false B
*a Matchmark


Put matchmarks on the steering sliding yoke sub-assembly and the steering link assembly.


b.

Loosen bolt A.


c.

Remove bolt B and separate the steering sliding yoke sub-assembly from the steering link assembly.


Hide 12.REMOVE STEERING COLUMN ASSEMBLY

a.
C382973

Disconnect all the connectors and disengage the 2 clamps to separate the wire harness from the steering column assembly.

NOTICE:

Do not pull the wire harness.



b.
C382974

Disconnect the 2 connectors from the power steering ECU assembly.


c.
C382975

Disengage the wire harness clamp to separate the wire harness from the power steering ECU assembly.

NOTICE:

Do not pull the wire harness.



d.
C385302

Remove the bolt, 2 nuts and the steering column assembly from the instrument panel reinforcement assembly.


Hide 45879A 13.REMOVE BREAK AWAY CAPSULE

a.

Remove the 2 break away capsules from the steering column assembly.