This DTC will be stored if the power steering ECU assembly determines that the assist map is not written in the ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition | Note |
|---|---|---|---|---|---|---|
| C1581 | Assist Map Number Un-Writing | Assist map not written in power steering ECU assembly | ·
CAN communication system ·
ECM ·
Skid control ECU (Brake actuator assembly) ·
Power steering ECU assembly |
EPS warning light: Comes on | Assist map written | - |
If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
Related parts store information necessary for assist map writing.
Related Part:
ECM
Skid control ECU (Brake actuator assembly)
Perform assist map writing.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
| Tester Display |
|---|
| Signal Check |
Check for DTCs.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1581 is output. | A |
| DTC C1581 is not output. | B |
DTC C1581 is cleared after the assist map is written.
A
B
Check for DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output. | A |
| CAN communication system DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Confirm if the related parts have the correct part number.
| Related Part | ECM |
| Skid control ECU (Brake actuator assembly) |
When removing the related part to check it, be sure to follow the appropriate procedures and precautions.
ECM
for 1NR-FE
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>ECM>REMOVAL
for 2NR-FE
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>ECM>REMOVAL
Skid control ECU (Brake actuator assembly)
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL
| Result | Proceed to |
|---|---|
| All of the related parts have the correct part number. | A |
| Any of the related parts have the incorrect part number. | B |
A
B
Select Health Check on the GTS screen and check if system DTCs of the related parts are output.
If system DTCs of the related parts are stored, assist map writing to the power steering ECU assembly may not be performed properly.
| Result | Proceed to |
|---|---|
| System DTCs of the related parts are output. | A |
| System DTCs of the related parts are not output. | B |
A
B
Replace the related parts with ones that have the correct part number.
ECM
for 1NR-FE
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>ECM>REMOVAL
for 2NR-FE
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>ECM>REMOVAL
Skid control ECU (Brake actuator assembly)
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B