Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT(for 1NR-FE) › from 2018.01
RM30M0E _52 Drivetrain _017091 C54 MANUAL TRANSMISSION / TRANSAXLE _0262467 MANUAL TRANSAXLE UNIT(for 1NR-FE) A

C54 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT(for 1NR-FE)  DISASSEMBLY  


PROCEDURE

Hide 31204 1.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31230 2.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31232A 3.REMOVE RELEASE BEARING HUB CLIP

Hide 31126 4.REMOVE CLUTCH RELEASE FORK BOOT

Hide 31236B 5.REMOVE RELEASE FORK SUPPORT

Hide 33823 6.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C295135

Remove the 3 bolts and No. 1 transmission control cable bracket from the manual transmission case.


Hide 33101A 7.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
C283060

Remove the manual transmission filler plug and gasket from the manual transmission case.


Hide 33104 8.REMOVE DRAIN PLUG SUB-ASSEMBLY

a.
C283061

Remove the drain plug sub-assembly and gasket from the manual transmission case.


Hide 84210 9.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
C295252

Using a 27 mm socket wrench, remove the back-up light switch assembly and gasket from the manual transmission case.


Hide 33111G 10.REMOVE MANUAL TRANSMISSION BREATHER PLUG

a.
C295138

Using a screwdriver, remove the manual transmission breather plug from the manual transmission case.


Hide 33590F 11.REMOVE FLOOR SHIFT SELECTING BELL CRANK ASSEMBLY

a.
C295139C01
0.219,1.302 1.167,0.875 true 1.49,1.813 1.844,0.885 true 0.031,1.24 0.344,1.396 0.313,0.156 10 false *1 1.396,1.833 1.708,1.99 0.313,0.156 10 false *2
*1 Floor Shift Selecting Bellcrank Assembly
*2 Control Bellcrank Dust Cover


Remove the 2 bolts and floor shift selecting bellcrank assembly with control bellcrank dust cover from the manual transmission case.


b.

Remove the control bellcrank dust cover from the floor shift selecting bellcrank assembly.


Hide 33544C 12.REMOVE SHIFT LEVER DAMPER

a.
C295140

Remove the 2 bolts and shift lever damper from the shift and select lever shaft assembly.


Hide 30300 13.SECURE MANUAL TRANSAXLE ASSEMBLY

a.
C295141C01
1.417,1.844 2.938,1.177 2.938,1.177 2.417,1.802 true 2.979,1.083 3.292,1.281 0.313,0.198 10 false *a
*a Wooden Block


Place the manual transaxle assembly on wooden blocks.


Hide 33295A 14.REMOVE REVERSE RESTRICT SHAFT

a.
C295142

Remove the reverse restrict shaft and washer from the manual transmission case.


Hide 33290B 15.REMOVE NO. 2 LOCK BALL ASSEMBLY

a.
C381204

Remove the No. 2 lock ball assembly from the manual transmission case.


Hide 16.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.
C295144

Remove the 4 bolts.


b.

Remove the shift and select lever shaft assembly and gasket from the manual transmission case.


Hide 33102 17.REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

a.
C295381

Remove the 9 bolts.


b.
C296454C01
0,0 0,0 false
V100135

Projection Part


Using a plastic hammer, carefully tap the projections of the manual transmission case cover sub-assembly to remove the manual transmission case cover sub-assembly from the manual transmission case.

NOTICE:

Do not damage the manual transmission case.



Hide 33321G 18.REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

a.
C251589E02
1.885,0.708 2.219,0.906 false 2.26,0.823 2.719,1.021 0.458,0.198 10 false SST

Using SST and a hammer, loosen the staked part of the manual transmission output shaft rear set nut.

SST
09930-00010  


b.
C282898

Engage the 2 gears simultaneously to lock the transmission.


c.

Using a 27 mm socket wrench, remove the manual transmission output shaft rear set nut.


d.

Disengage the 2 gears.


Hide 33214G 19.REMOVE NO. 3 GEAR SHIFT FORK

a.
C282899

Remove the No. 3 gear shift fork set bolt from the No. 3 gear shift fork.


b.
C282900

Remove the No. 3 transmission hub sleeve with the No. 3 gear shift fork from the No. 3 transmission clutch hub.


c.

Remove the No. 3 gear shift fork from the No. 3 transmission hub sleeve.


Hide 20.INSPECT 5TH GEAR THRUST CLEARANCE

a.
C282901

Using a dial indicator, measure the 5th gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0216 in.)


Maximum clearance:

0.55 mm (0.0216 in.)


If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, 5th gear or input shaft rear radial ball bearing.


Hide 21.INSPECT 5TH GEAR RADIAL CLEARANCE

a.
C282902

Using a dial indicator, measure the 5th gear radial clearance.

Standard clearance:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft.


Hide 33395 22.REMOVE NO. 3 TRANSMISSION CLUTCH HUB

a.
C282903

Using 2 screwdrivers and a hammer, tap out the snap ring.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
C157373

Using a screwdriver, remove the synchromesh shifting key spring from the No. 3 transmission clutch hub.


c.
C287902C01
1.188,1.448 0.521,1.552 0.521,1.552 1.021,0.969 true 0.219,1.469 0.677,1.667 0.458,0.198 10 false SST 1.948,0.292 2.26,0.49 0.313,0.198 10 false *b 0.313,1.146 0.625,1.344 0.313,0.198 10 false *a
*a Hold
*b Turn


Using SST, remove the No. 3 transmission clutch hub, 5th gear and No. 3 synchronizer ring from the input shaft.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031, 09957-04010)
09950-60010  (09951-00200)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



d.
C282905

Remove the 3 synchromesh shifting keys and synchromesh shifting key spring from the No. 3 transmission clutch hub.


Hide 33336A 23.REMOVE 5TH GEAR NEEDLE ROLLER BEARING

a.
C296763C02
1.854,1.729 1.49,1.208 true 0.646,0.729 1.26,0.958 true 0.458,0.646 0.771,0.802 0.313,0.156 10 false *1 1.802,1.771 2.115,1.927 0.313,0.156 10 false *2
*1 5th Gear Needle Roller Bearing
*2 5th Gear Bearing Spacer


Remove the 5th gear needle roller bearing and 5th gear bearing spacer from the input shaft.


Hide 33428C 24.REMOVE 5TH DRIVEN GEAR

a.
C287904C01
1.427,1.417 0.75,1.167 0.75,1.167 1.281,0.948 true 0.438,1.083 0.896,1.281 0.458,0.198 10 false SST 0.333,0.542 0.646,0.74 0.313,0.198 10 false *a 1.854,0.177 2.167,0.375 0.313,0.198 10 false *b
*a Hold
*b Turn


Using SST, remove the 5th driven gear from the output shaft.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03021)
09950-60010  (09951-00180, 09952-06010)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



Hide 33151D 25.REMOVE REAR BEARING RETAINER

a.
C296753

Remove the 5 bolts and rear bearing retainer from the manual transmission case.


Hide 33111R 26.REMOVE OUTPUT SHAFT REAR BEARING HOLE SNAP RING

a.
C282909

Using a snap ring expander, remove the output shaft rear bearing hole snap ring from the output shaft.


Hide 33311X 27.REMOVE INPUT SHAFT REAR BEARING HOLE SNAP RING

a.
C282910

Using a snap ring expander, remove the input shaft rear bearing hole snap ring from the input shaft.


Hide 33451H 28.REMOVE REVERSE IDLER GEAR SHAFT BOLT

a.
C282911

Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.


Hide 33242E 29.REMOVE SHIFT FORK SHAFT SNAP RING

a.
C282912

Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 2 gear shift fork shaft.

HINT:

Use a piece of cloth to keep the shift fork shaft snap ring from flying off.



Hide 33275C 30.REMOVE SHIFT DETENT BALL

a.
C296754

Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case.


b.
C296755

Using a magnet hand, remove the 2 spring seats, 2 compression springs and 2 shift detent balls from the manual transmission case.


c.
C282915

Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the transaxle case.


d.
C282916

Using a magnet hand, remove the spring seat, compression spring and shift detent ball from the transaxle case.


Hide 33290 31.REMOVE NO. 1 LOCK BALL ASSEMBLY

a.
C282917

Using a 6 mm hexagon socket wrench, remove the No. 1 lock ball assembly from the manual transmission case.


Hide 33111 32.REMOVE MANUAL TRANSMISSION CASE

a.
C294929

Remove the 3 bolts from the transaxle case.


b.
C294665C01
0.396,0.948 0.802,0.927 true 0.188,0.875 0.5,1.031 0.313,0.156 10 false *1
*1 Clutch Tube Bracket


Remove the 13 bolts and clutch tube bracket from the manual transmission case.


c.
C282919

Using a brass bar and a hammer, carefully tap the projections of the manual transmission case to remove the manual transmission case from the transaxle case.

NOTICE:

Do not damage the manual transmission case and transaxle case.



Hide 33402 33.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C296756C01
1.146,0.74 1.604,0.74 true 1.135,1.031 1.594,1.031 true 0.896,1.219 1.354,1.219 true 0.719,1.135 0.958,1.375 0.24,0.24 10 true *1 0.948,0.656 1.198,0.885 0.25,0.229 10 true *3 0.938,0.938 1.177,1.177 0.24,0.24 10 true *2
*1 Reverse Idler Gear Sub-assembly
*2 Reverse Idler Gear Thrust Washer
*3 Reverse Idler Gear Shaft


Remove the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft from the transaxle case.


Hide 33240 34.REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY

a.
C296757

Remove the 2 bolts and reverse shift arm bracket assembly from the transaxle case.


Hide 33243A 35.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

a.
C282922

Remove the No. 2 gear shift fork set bolt and No. 1 gear shift head set bolt from the No. 2 gear shift fork and No. 1 gear shift head.


b.
C282923C01
1.76,0.438 2.542,0.438 true 1.271,1.927 1.563,1.375 true 1.177,1.927 1.49,2.125 0.313,0.198 10 false *1 2.573,0.354 2.885,0.552 0.313,0.198 10 false *2
*1 No. 1 Gear Shift Head
*2 No. 2 Gear Shift Fork Shaft


Remove the No. 2 gear shift fork shaft and No. 1 gear shift head from the transaxle case.


Hide 33212A 36.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
C282924

Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring.

HINT:

Use a piece of cloth to keep the shift fork shaft snap ring from flying off.



b.
C282925C01
1.896,0.667 2.76,0.25 true 2.802,0.156 3.115,0.354 0.313,0.198 10 false *1
*1 No. 1 Gear Shift Fork Shaft


Remove the No. 1 gear shift fork set bolt and No. 1 gear shift fork shaft from the No. 1 gear shift fork.


c.
C282926

Remove the No. 1 gear shift fork.


Hide 33244G 37.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
C282927

Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 3 gear shift fork shaft.

HINT:

Use a piece of cloth to keep the shift fork shaft snap ring from flying off.



b.
C282928C01
2.01,0.271 2.344,0.271 true 2.198,0.583 2.448,0.583 false 2.271,1.219 2.99,1.219 true 2.385,0.167 2.698,0.365 0.313,0.198 10 false *1 2.5,0.5 2.813,0.698 0.313,0.198 10 false *2 3.031,1.125 3.344,1.323 0.313,0.198 10 false *3
*1 No. 3 Gear Shift Fork Shaft
*2 No. 2 Gear Shift Fork
*3 Reverse Shift Fork


Remove the No. 3 gear shift fork shaft together with the reverse shift fork and No. 2 gear shift fork from the transaxle case.


c.
C282929

Using a magnet hand, remove the 2 reverse shift fork balls from the reverse shift fork.


d.
C282930

Secure the No. 3 gear shift fork shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 3 gear shift fork shaft.

HINT:

Use a piece of cloth to keep the shift fork shaft snap ring from flying off.



f.

Remove the reverse shift fork from the No. 3 gear shift fork shaft.


Hide 38.REMOVE INPUT SHAFT ASSEMBLY

a.
C282931

Remove the input shaft assembly and output shaft assembly from the transaxle case.


Hide 39.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C282932

Remove the differential case assembly from the transaxle case.


Hide 33125 40.REMOVE MANUAL TRANSAXLE CASE RECEIVER

a.
C282933

Remove the bolt and manual transaxle case receiver from the transaxle case.


Hide 33280 41.REMOVE REVERSE RESTRICT PIN ASSEMBLY

a.
C294737

Using a 6 mm hexagon socket wrench, remove the reverse restrict pin plug from the manual transmission case.


b.
C295243

Using a 5 mm pin punch and a hammer, drive out the reverse restrict pin slotted spring pin and remove the reverse restrict pin assembly from the manual transmission case.


Hide 33124C 42.REMOVE NO. 1 OIL RECEIVER PIPE

a.
C282936

Remove the bolt and No. 1 oil receiver pipe from the manual transmission case.

NOTICE:

Do not damage the No. 1 oil receiver pipe.



Hide 33124D 43.REMOVE NO. 2 OIL RECEIVER PIPE

a.
C296758

Remove the bolt and No. 2 oil receiver pipe from the manual transmission case.

NOTICE:

Do not damage the No. 2 oil receiver pipe.



Hide 33326 44.REMOVE BEARING LOCK PLATE

a.
C282938

Remove the bolt and bearing lock plate from the transaxle case.


Hide 33449 45.REMOVE TRANSMISSION MAGNET

a.
C282939

Remove the transmission magnet from the transaxle case.


Hide 33311A 46.REMOVE INPUT SHAFT FRONT BEARING

a.
C296748C01
1.667,1.167 1.521,0.906 true 0.573,0.417 0.885,0.573 0.313,0.156 10 false *a 2.365,1.177 2.677,1.333 0.313,0.156 10 false *b 1.198,0.823 1.51,0.979 0.313,0.156 10 true SST
*a Hold
*b Turn


Using SST, remove the input shaft front bearing from the transaxle case.

SST
09612-65014  (09612-01050, 09612-01060)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



Hide 31105D 47.REMOVE FRONT TRANSAXLE CASE OIL SEAL

a.
C267940C01
1.24,1.156 0.417,0.688 true 0.24,0.563 0.427,0.729 0.188,0.167 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the front transaxle case oil seal from the transaxle case.

NOTICE:

Make sure not to damage the inside of the transaxle case.



Hide 33321N 48.REMOVE OUTPUT SHAFT FRONT BEARING

a.
C296749C01
1.063,0.635 1.5,0.74 true 0.74,0.563 1.198,0.76 0.458,0.198 10 false SST

Using SST, remove the output shaft front bearing from the transaxle case.

SST
09308-00010  

NOTICE:

Do not apply excessive force to the transaxle case when using SST.



Hide 33134B 49.REMOVE OUTPUT SHAFT COVER

a.
C282943

Remove the output shaft cover from the transaxle case.


Hide 41311E 50.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C287905C01
0.615,1.823 1.042,1.5 true 0.302,1.74 0.76,1.938 0.458,0.198 10 false SST 0.625,0.583 0.938,0.781 0.313,0.198 10 true *a 1.667,0.74 1.979,0.938 0.313,0.198 10 true *b
*a Hold
*b Turn


Using SST, remove the front differential case front tapered roller bearing (outer race) and front differential case front plate washer from the transaxle case.

SST
09612-65014  (09612-01040, 09612-01050)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



b.
C287906C02
1.75,1.25 2.5,1.26 2.5,1.26 1.802,1.313 true 2.104,1.49 2.51,1.26 2.51,1.26 2.052,0.813 false 2.542,1.188 3,1.385 0.458,0.198 10 false SST 0.583,0.938 0.896,1.135 0.313,0.198 10 false *a 2.594,0.583 2.906,0.781 0.313,0.198 10 false *b
*a Hold
*b Turn


Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00360)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



Hide 43410M 51.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C282946E01
1.594,1.479 1.26,1.24 1.26,1.24 1.698,0.938 true 0.896,1.135 1.208,1.365 0.313,0.229 10 true SST

Using SST and a hammer, drive out the front drive shaft oil seal RH from the transaxle case.

SST
09950-60010  (09951-00530)
09950-70010  (09951-07150)


Hide 41311F 52.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C287908C01
0.802,0.823 1.167,1.083 true 0.51,0.74 0.844,1.031 0.333,0.292 10 false SST 0.677,0.438 1.01,0.729 0.333,0.292 10 false *a 1.865,0.521 2.198,0.813 0.333,0.292 10 false *b
*a Hold
*b Turn


Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear plate washer from the manual transmission case.

SST
09612-65014  (09612-01040, 09612-01050)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



b.
C287907C02
1.896,1.521 2.719,1.708 2.719,1.708 2.5,1.448 true 2.771,1.677 3.229,1.875 0.458,0.198 10 false SST 0.208,0.521 0.667,0.719 0.458,0.198 10 false *a 2.365,0.438 2.823,0.635 0.458,0.198 10 false *b
*a Hold
*b Turn


Using SST, remove the front differential case rear tapered roller bearing (inner race) from the differential case assembly.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00360)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



Hide 43420H 53.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C282949E01
1.625,1.375 1.219,0.333 1.219,0.333 1.708,0.552 true 0.917,0.24 1.375,0.438 0.458,0.198 10 false SST

Using SST and a hammer, drive out the front drive shaft oil seal LH from the manual transmission case.

SST
09950-60010  (09951-00530)
09950-70010  (09951-07150)