Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › from 2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the driver door only, but the entry unlock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the driver door lock position switch system.

WIRING DIAGRAM

B359348E05
0.948,1.854 2.615,2.25 1.667,0.396 10 false Front Door Lock Assembly (for Driver Door) 0.594,1.25 0.771,1.438 0.177,0.188 10 false 8 0.906,1.25 1.083,1.438 0.177,0.188 10 false 7 2.5,1.24 2.677,1.427 0.177,0.188 10 false 8 2.833,1.24 3.01,1.427 0.177,0.188 10 false 7 0.531,1.448 0.792,1.635 0.26,0.188 10 false G2 0.875,1.448 1.135,1.635 0.26,0.188 10 false H3 2.458,1.448 2.719,1.635 0.26,0.188 10 false H3 2.781,1.448 3.042,1.635 0.26,0.188 10 false G2 0.573,1.615 0.833,1.802 0.26,0.188 10 false *2 0.875,1.615 1.135,1.802 0.26,0.188 10 false *1 2.479,1.615 2.74,1.802 0.26,0.188 10 false *1 2.792,1.615 3.052,1.802 0.26,0.188 10 false *2 1.135,1.333 1.521,1.531 0.385,0.198 10 false E 1.99,1.333 2.385,1.51 0.396,0.177 10 false LSSR 0.146,3.042 1.563,3.313 1.417,0.271 10 false *1: for LHD 0.156,3.385 1.573,3.656 1.417,0.271 10 false *2: for RHD 3.583,1.427 4.073,1.604 0.49,0.177 10 false LSWD 4.115,1.198 4.51,1.375 0.396,0.177 10 false PRG 4.115,1.698 4.51,1.875 0.396,0.177 10 false RDA 4.469,1.104 4.646,1.292 0.177,0.188 10 false 9 4.458,1.604 4.635,1.792 0.177,0.188 10 false 16 5.563,1.104 5.74,1.292 0.177,0.188 10 false 36 5.563,1.583 5.74,1.771 0.177,0.188 10 false 13 5.792,1.188 6.229,1.375 0.438,0.188 10 false PRG3 5.792,1.677 6.24,1.875 0.448,0.198 10 false RDA3 3.531,2.469 3.844,2.656 0.313,0.188 10 false F52 3.531,2.615 4.615,2.906 1.083,0.292 10 false Body Computer 5.49,2.458 5.802,2.646 0.313,0.188 10 false F44 5.5,2.615 7.031,3.094 1.531,0.479 10 false Certification ECU (Smart Key ECU Assembly) 3.313,1.333 3.49,1.521 0.177,0.188 10 false 15

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR)

NG

2.INSPECT FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR)
a.

Remove the front door lock assembly (for driver door).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.

Inspect the front door lock assembly (for driver door).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BODY COMPUTER - FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR))

NG

REPLACE FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR)

3.CHECK HARNESS AND CONNECTOR (BODY COMPUTER - FRONT DOOR LOCK ASSEMBLY (FOR DRIVER DOOR))
a.

Disconnect the F52 body computer connector.


b.

Disconnect the H3*1 or G2*2 front door lock assembly (for driver door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F52-15 (LSWD) - H3-8 (LSSR) Always Below 1 Ω
H3-7 (E) - Body ground Always Below 1 Ω
F52-15 (LSWD) or H3-8 (LSSR) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F52-15 (LSWD) - G2-7 (LSSR) Always Below 1 Ω
G2-8 (E) - Body ground Always Below 1 Ω
F52-15 (LSWD) or G2-7 (LSSR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK ENTRY DOOR LOCK OPERATION
5.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the entry lock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry lock operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG