Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › from 2018.01
RM30M0E _53 Suspension _017095 FRONT SUSPENSION _0090096 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 2.REMOVE FRONT WHEEL

Hide 48810 3.SEPARATE FRONT STABILIZER LINK ASSEMBLY (w/ Side Rail Reinforcement)

a.
C385290

Remove the nut to separate the front stabilizer link assembly from the front shock absorber with coil spring.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 47313A 4.SEPARATE FRONT FLEXIBLE HOSE

Hide 5.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C230948C03
2.979,1.448 2.625,1.448 false 2.833,3.563 2.625,3.563 false 1.177,4.177 1.552,4.385 false 3.042,1.354 3.302,1.583 0.26,0.229 10 false *a 2.917,3.427 3.177,3.656 0.26,0.229 10 false *b 0.969,4.031 1.229,4.26 0.26,0.229 10 false *c
*a Jack Point
*b Wooden Block
*c Jack


Support the front axle using a jack and wooden block.


b.
C294133

Remove the 2 nuts and 2 bolts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

HINT:

Keep the bolt from rotating while turning the nut.



c.
C285276C01
0.969,1.906 1.281,2.063 0.313,0.156 10 false *a 2.177,0.302 2.49,0.458 0.313,0.156 10 false *b
*a Turn
*b Hold


Using a 6 mm hexagon socket wrench, fix the shock absorber rod in place and remove the nut.


d.

Remove the front No. 2 suspension support.


e.

Remove the front shock absorber with coil spring from the vehicle.


Hide 48304 6.DISCONNECT FRONT SPRING BUMPER SUB-ASSEMBLY

a.
C362064C02
0.51,1.146 1.26,1.313 false 1.302,1.229 1.708,1.625 true 0.323,1.031 0.635,1.188 0.313,0.156 10 false *1 1.75,1.594 2.063,1.75 0.313,0.156 10 false *a
*1 Front Spring Bumper
*a Claw


Disconnect the front spring bumper sub-assembly from the claws of the front shock absorber assembly.


Hide 48609E 7.REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C287918N05
2.385,1.271 2.667,0.979 false 2.708,0.896 3.167,1.094 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-30022  (09727-00010, 09727-00022, 09727-00031)


b.
C298400C16
2.927,1.719 2.604,2.021 2.604,2.021 2.26,1.74 false 2.927,3.906 2.542,4.177 2.542,4.177 2.167,3.875 false 0.208,0.26 0.521,0.417 0.313,0.156 10 false *a 0.25,2.563 0.563,2.719 0.313,0.156 10 false *b 2.552,2.042 2.865,2.198 0.313,0.156 10 false *c 2.469,4.188 2.781,4.344 0.313,0.156 10 false *d
*a Correct
*b Incorrect
*c Parallel
*d Not Parallel


Attach the hooks of each SST arm across the diameter of the front coil spring.

CAUTION:
·

Make sure that the hooks of the upper and lower arms are attached to the front coil spring so that the distance between the hooks is as large as possible.

·

Make sure that the arms of SST are parallel and attached to the front coil spring, and the number of front coil springs between the hooks on each side is the same.

·

Check that the claws of the hooks are securely attached to the front coil spring.




c.
C302415C09
1.469,1.49 1.469,1.031 false 3.135,1.479 3.135,1.021 false 0.031,0.063 0.302,0.26 0.271,0.198 10 false *a 1.563,0.073 1.813,0.281 0.25,0.208 10 false *b 1.406,1.5 1.719,1.656 0.313,0.156 10 false *c 3.073,1.49 3.385,1.646 0.313,0.156 10 false *c
*a Correct
*b Incorrect
*c Stopper Pin


Install the stopper pins to the hooks of SST.

CAUTION:

Make sure that the stopper pins are installed securely.



d.

Using SST, compress the front coil spring.

CAUTION:
·

If the front coil spring buckles while using SST, stop immediately and reattach SST correctly.

·

Do not compress the front coil spring to the point where the coils touch each other.

·

Do not use an impact wrench.

·
C303008N01
1.521,1.438 2.115,1.281 true 2.167,1.208 2.625,1.406 0.458,0.198 10 false SST

If a stopper pin touches the front coil spring while using SST, remove the stopper pin and continue with the procedure. In this case, installing the coil spring stopper belt as shown in the illustration is recommended.



SST
09727-00110  


e.
C303010C01
2.646,1.865 2.854,2.052 0.208,0.188 10 true *a 0.781,1.688 1.094,1.844 0.313,0.156 10 false *b
*a Turn
*b Hold


Check that the front coil spring has become detached, and then using a 6 mm hexagon socket wrench, hold the front shock absorber rod and remove the front support to front shock absorber nut.

CAUTION:

Do not remove the front support to front shock absorber nut if the coil spring is not free.



Hide 48609 8.REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.

Remove the front suspension support sub-assembly from the front shock absorber assembly.


Hide 48619A 9.REMOVE STRUT MOUNTING BEARING

a.

Remove the strut mounting bearing from the front upper coil spring seat.


Hide 48304 10.REMOVE FRONT SPRING BUMPER SUB-ASSEMBLY

a.

Remove the front spring bumper sub-assembly from the front shock absorber assembly.


Hide 48520 11.REMOVE FRONT SHOCK ABSORBER ASSEMBLY

a.

Remove the front shock absorber assembly.


Hide 48158C 12.REMOVE FRONT COIL SPRING LOWER INSULATOR

a.

Remove the front coil spring lower insulator from the front shock absorber assembly.


Hide 48132 13.REMOVE FRONT COIL SPRING

a.

Remove the front coil spring from SST.

NOTICE:

Do not use an impact wrench. It will damage SST.