Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT › from 2017.10
RM30M0E _52 Drivetrain _017093 AXLE AND DIFFERENTIAL _0090086 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 47313A 2.SEPARATE FRONT FLEXIBLE HOSE

a.
C283559

Remove the bolt and separate the front flexible hose and front speed sensor wire from the front shock absorber assembly.


Hide 3.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.
C282312

Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Hang the front disc brake caliper assembly using a piece of string or the equivalent.



Hide 43512 4.REMOVE FRONT DISC

Hide 43502D 5.REMOVE FRONT AXLE HUB BOLT

C282313C01
1.271,1.958 1.063,1.354 true 1.26,1.021 0.531,0.635 true 1.521,1.063 1.615,0.427 true 1.313,1.885 1.625,2.042 0.313,0.156 10 true *a 1.885,1.583 2.198,1.74 0.313,0.156 10 false *b 0.646,1.677 0.958,1.833 0.313,0.156 10 false *c 0.406,0.563 0.552,0.74 0.146,0.177 10 true *a 1.646,0.323 2.021,0.521 0.375,0.198 10 false SST
*a Service Nut
*b Turn
*c Hold


a.

Temporarily install the 2 service nuts to the 2 front axle hub bolts as shown in the illustration.

Recommended Service Nut:
Thread Diameter Thread Pitch
12.0 mm (0.472 in.) 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the front axle hub bolts.



b.

Using SST and a screwdriver or the equivalent to hold the front axle hub sub-assembly, remove the front axle hub bolt.

SST
09611-12010  


Hide 43502D 6.INSTALL FRONT AXLE HUB BOLT

a.

Temporarily install a new front axle hub bolt to the front axle hub sub-assembly.


b.
C282314C01
2.74,0.292 2.583,0.417 false 2.844,0.552 3.073,0.427 false 2.604,0.802 2.729,0.802 false 2.771,0.208 3.083,0.365 0.313,0.156 10 false *a 3.083,0.323 3.365,0.479 0.281,0.156 10 false *b 2.344,1.719 2.604,1.875 0.26,0.156 10 false *c 0.25,1.406 0.49,1.604 0.24,0.198 10 false *d
*a Washer
*b Service Nut
*c Turn
*d Hold


Install a washer and service nut to the front axle hub bolt as shown in the illustration.

Recommended Service Nut:
Thread Diameter Thread Pitch
12.0 mm (0.472 in.) 1.5 mm (0.0591 in.)


HINT:

Recommended thickness of the washer is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or the equivalent to hold the front axle hub sub-assembly, install the front axle hub bolt by tightening the service nut.


Hide 43512 7.INSTALL FRONT DISC

Hide 8.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
106.8 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 47313A 9.INSTALL FRONT FLEXIBLE HOSE

a.

Install the front flexible hose and front speed sensor wire to the front shock absorber assembly with the bolt.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose and front speed sensor wire without twisting them.


HINT:

Install the front speed sensor harness bracket first and then the front flexible hose bracket.



Hide 10.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)