CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY COMPUTER
| *1 | Driver Side Junction Block Assembly | - | - |
| *1 | Body Computer | - | - |
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-1 (GND) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-6 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-7 (IG) - Body ground | - | Ignition switch power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the body computer to the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 6J-3 (ACT-) - Body ground | R - Body ground*4
W - Body ground*5 |
Door lock motor unlock drive output | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked | 11 to 14 V | |||
| 6J-4 (ACT+) - Body ground | SB - Body ground*4
GR - Body ground*5 |
Door lock motor lock drive output | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder locked | 11 to 14 V | |||
| 6M-2 (DCTY) - Body ground | BR - Body ground | Driver side door courtesy light switch input | Driver side door open | Below 1 V |
| Driver side door closed | Pulse generation | |||
| 6M-4 (DCTY) - Body ground | BR - Body ground | Driver side door courtesy light switch input | Driver side door open | Below 1 V |
| Driver side door closed | Pulse generation | |||
| F52-14 (PCTY) - Body ground | LG - Body ground | Except driver side door courtesy light switch input | Except driver side door open | Below 1 V |
| All doors except driver side door closed | Pulse generation | |||
| F52-19 (L1) - Body ground | W - Body ground | Door control switch input | Door control switch locked | Below 1 V |
| Door control switch off | Pulse generation | |||
| F52-12 (UL1) - Body ground | R - Body ground | Door control switch input | Door control switch unlocked | Below 1 V |
| Door control switch off | Pulse generation | |||
| F52-18 (L2) - Body ground | V - Body ground | Driver door key-linked lock input | Driver door key cylinder turned to lock position | Below 1 V |
| Driver door key cylinder off | Pulse generation | |||
| F52-11 (UL2) - Body ground | BE - Body ground*6
L - Body ground*7 |
Driver door key-linked unlock input | Driver door key cylinder turned to unlock position | Below 1 V |
| Driver door key cylinder off | Pulse generation | |||
| F52-15 (LSWD) - Body ground | W - Body ground | Driver side door unlock detection switch input | Driver side door unlocked | Below 1 V |
| Driver side door locked | Pulse generation | |||
| F52-8 (KSW) - Body ground*1 | SB - Body ground | Unlock warning switch input | No key in ignition key cylinder | Pulse generation |
| Key in ignition key cylinder | Below 1 V | |||
| 6I-2 (GSW) - Body ground*4 | L - Body ground | Collision detection input | Ignition switch ON | 2.8 V to 4.3 V |
| 6M-5 (DBKL) - Body ground | R - Body ground | Front seat inner belt assembly LH signal*6 | Ignition switch ON
Front seat belt is unfastened |
Below 1 V |
| Ignition switch ON
Front seat belt is fastened |
Pulse generation | |||
| Front seat inner belt assembly RH signal*7 | Ignition switch ON
Front seat belt is unfastened |
Below 1 V | ||
| Ignition switch ON
Front seat belt is fastened |
Pulse generation | |||
| 6N-1 (BCTY) - Body ground*3 | R - Body ground | Back door courtesy light switch input | Back door open | Below 1 V |
| Back door closed | 11 to 14 V | |||
| 6N-3 (BDSU) - Body ground*1, *3 | G - Body ground | Back door opener switch input | Back door opener switch (open switch) pressed | Below 1 V |
| Back door opener switch (open switch) not pressed | Pulse generation | |||
| 6J-2 (TR+) - Body ground*3 | L - Body ground | Door lock motor lock drive output (Back door) | Back door closed | Below 1 Ω |
| Back door opener switch (open switch) pressed | 11 to 14 V | |||
| F52-16 (RDA) - Body ground*2 | GR - Body ground | Signal input from certification ECU (smart key ECU assembly) | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F52-9 (PRG) - Body ground*2 | BR - Body ground | Signal output to certification ECU (smart key ECU assembly) | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F125 -1 (ACTG) - Body ground*4 | L - Body ground | Collision door lock release signal | Collision door lock release function does not operate | Below 2 V*8
7.3 to 9.9 V*9 |
| Collision door lock release function operates | Below 1 V |
*1: w/o Smart Entry and Start System
*2: w/ Smart Entry and Start System
*3: for Hatchback
*4: w/ Door Control Battery
*5: w/o Door Control Battery
*6: for LHD
*7: for RHD
*8: Door control battery not charged
*9: Door control battery charging or charged
If the result is not as specified, the body computer or driver side junction block assembly may be malfunctioning.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (for Hatchback (w/ Smart Entry and Start System))
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F43-10 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| F43-14 (TSW5) - Body ground | G - Body ground | Back door opener switch input | Back door opener switch (open switch) pressed | Below 1 Ω |
| Back door opener switch (open switch) not pressed | 10 kΩ or higher | |||
| F43-23 (TSW6) - Body ground | L - Body ground | Back door opener switch input | Back door opener switch (lock switch) pressed | Below 1 Ω |
| Back door opener switch (lock switch) not pressed | 10 kΩ or higher |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F44-13 (RDA3) - F43-10 (E) | GR - W-B | Signal output to body computer | Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F44-36 (PRG3) - F43-10 (E) | BR - W-B | Signal input from body computer | Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F43-14 (TSW5) - F43-10 (E) | G - W-B | Back door opener switch signal | Back door opener switch (open switch) pressed | Below 1.5 V |
| Back door opener switch (open switch) not pressed | 4.5 V or higher | |||
| F43-23 (TSW6) - F43-10 (E) | L - W-B | Back door opener switch signal | Back door opener switch (lock switch) pressed | Below 1.5 V |
| Back door opener switch (lock switch) not pressed | 4.5 V or higher |
If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.