CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY COMPUTER
| *1 | Driver Side Junction Block Assembly | - | - |
| *1 | Body Computer | - | - |
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-1 (GND) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-6 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-7 (IG) - Body ground | - | Ignition switch power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the body computer to the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 6J-3 (ACT-) - Body ground | W - Body ground | Door lock motor unlock drive output (all door) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked | 11 to 14 V | |||
| 6J-4 (ACT+) - Body ground | GR - Body ground | Door lock motor lock drive output (front door) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder locked | 11 to 14 V | |||
| 6M-2 (DCTY) - Body ground | BR - Body ground | Driver door courtesy light switch input | Driver door open | Below 1 V |
| Driver door closed | Pulse generation | |||
| 6M-4 (DCTY) - Body ground | BR - Body ground | Driver door courtesy light switch output | Driver door open | Below 1 V |
| Driver door closed | Pulse generation | |||
| F52-14 (PCTY) - Body ground | LG - Body ground | Except driver door courtesy light switch input | Except driver door open | Below 1 V |
| All doors except driver door closed | Pulse generation | |||
| F52-15 (LSWD) - Body ground | L - Body ground*3
W - Body ground*4 |
Driver door unlock detection switch input | Driver door unlocked | Below 1 V |
| Driver door locked | Pulse generation | |||
| F52-9 (PRG) - Body ground | BR - Body ground | Signal output to door control receiver | Key inserted into ignition key cylinder → Key pulled out of ignition key cylinder | 11 to 14 V → Pulse generation → 11 to 14 V |
| F52-16 (RDA) - Body ground | G - Body ground | Signal input from door control receiver | Ignition switch off, all doors closed and door control transmitter assembly switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and door control transmitter assembly switch pressed | Pulse generation | |||
| F52-8 (KSW) - Body ground | SB - Body ground | Unlock warning switch input | No key in ignition key cylinder | Pulse generation |
| Key in ignition key cylinder | Below 1 V | |||
| F52-6 (HAZ) - Body ground | P- Body ground | Hazard warning signal output | Answer-back off | 11 to 14 V |
| Answer-back on | Below 1 V | |||
| 6N-1 (BCTY) - Body ground*1 | R- Body ground | Back door courtesy light switch input | Back door open | Below 1 V |
| Back door closed | 11 to 14 V | |||
| 6N-1 (LGCY) - Body ground*2 | R- Body ground | Luggage compartment door courtesy light switch input | Luggage compartment door open | Below 1 V |
| Luggage compartment door closed | 11 to 14 V |
*1: for Hatchback
*2: for Sedan
*3: for LHD
*4: for RHD
If the result is not as specified, the body computer or driver side junction block assembly may be malfunctioning.
CHECK DOOR CONTROL RECEIVER
Disconnect the door control receiver connector.
Measure the resistance and voltage according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F47-5 (+B) - Body ground | L - Body ground | Battery (power supply) | Always | 11 to 14 V |
| F47-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F47 door control receiver connector.
Measure the voltage and check for pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F47-2 (RDA) - F47-1 (GND) | G - W-B | Signal output to body computer | Ignition switch off, all doors closed and door control transmitter assembly switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and door control transmitter assembly switch pressed | Pulse generation | |||
| F47-3 (PRG) - F47-1 (GND) | BR - W-B | Signal input from body computer | Key inserted into ignition key cylinder → Key pulled out of ignition key cylinder | 11 to 14 V → Pulse generation → 11 to 14 V |
If the result is not as specified, the door control receiver may be malfunctioning.