Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT › 2020.03–2020.07
RM36W0E _53 Suspension _087257 ALIGNMENT / HANDLING DIAGNOSIS _0417578 REAR WHEEL ALIGNMENT G

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT  INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the rear wheel alignment procedure are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

PROCEDURE

Hide 3.INSPECT CAMBER

NOTICE:

Inspect while the vehicle is unloaded.


a.
C107736C10
2.052,1.26 2.375,1.26 false 2.406,1.167 2.656,1.385 0.25,0.219 10 *a
*a Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle):

-1°03' +/- 0°30' (-1.05° +/- 0.50°)


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.



Hide 4.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N (for CVT, Hybrid Transaxle).


c.

Release the parking brake and move the shift lever to neutral (for Manual Transaxle).


d.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


e.
C188968C02
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


f.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.



g.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle):
Engine Transaxle Tire Size Specified Condition
M15A-FKS M/T 175/70R14 C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.2 +/- 3.0 mm (0.165 +/- 0.118 in.)
185/60R15 C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.2 +/- 3.0 mm (0.165 +/- 0.118 in.)
185/55R16 C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.)
CVT 175/70R14 C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.2 +/- 3.0 mm (0.165 +/- 0.118 in.)
185/60R15 C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.2 +/- 3.0 mm (0.165 +/- 0.118 in.)
185/55R16 C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.)
M15A-FXE - 175/70R14 C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°)
B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.)
185/60R15 C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°)
B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.)
185/55R16 C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°)
B - A: 4.4 +/- 3.0 mm (0.173 +/- 0.118 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.


Hide 5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.INSPECT AND ADJUST HEADLIGHT AIMING

HINT:

These procedures are to be performed when suspension or tires components have been removed or replaced.