Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › 2020.03–2020.07
RM36W0E _53 Suspension _087263 FRONT SUSPENSION _0417616 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front suspension crossmember sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2. SECURE STEERING WHEEL

a.
C431683

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 45259A 3.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 4.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 5.REMOVE FRONT WHEELS

Hide 51451A 6.REMOVE CENTER ENGINE UNDER COVER

a.
C431863

Remove the 4 bolts, 4 screws, 9 clips and center engine under cover from the vehicle body.


Hide 51442C 7.REMOVE ENGINE UNDER COVER LH

a.
A461618

Remove the 2 clips and engine under cover LH from the vehicle body.


Hide 51441C 8.REMOVE ENGINE UNDER COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 53876A 9.SEPARATE FRONT FENDER LINER LH

a.
C429669

Remove the 2 screws and separate the front fender liner LH.


Hide 53875A 10.SEPARATE FRONT FENDER LINER RH

HINT:

Perform the same procedure as for the LH side.


Hide 51447D 11.REMOVE CENTER NO. 4 ENGINE UNDER COVER

a.
C431773

Remove the 2 bolt, 2 nuts and center No. 4 engine under cover from the vehicle body.


Hide 48810 12.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

a.
C427880

Remove the nut and separate the front stabilizer link assembly LH from the front stabilizer bar.

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 13.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 14.SEPARATE TIE ROD END SUB-ASSEMBLY LH

a.
C428598

Remove the cotter pin and nut.


b.
C428599N01
2.406,1.531 2.677,1.219 false 2.094,1.438 2.552,1.635 0.458,0.198 10 false SST

Install SST to the tie rod end sub-assembly LH.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the upper ends of the tie rod end sub-assembly LH and SST are aligned.



c.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.



d.

Using SST, separate the tie rod end sub-assembly LH from the steering knuckle LH.

SST
09960-20010  (09961-02010)

C428600C01
1.083,2.75 1.25,2.583 false 0.333,1.083 0.583,1.083 true 3.333,2.917 3.333,2.667 false 0.167,1 0.333,1.167 0.167,0.167 10 true *a 6.583,0.844 6.896,1 0.313,0.156 10 false *c 2.667,1.083 2.979,1.24 0.313,0.156 10 false *d 0.26,2.833 0.667,3.167 0.406,0.333 10 false A 0.25,3.042 0.656,3.375 0.406,0.333 10 false B 5.521,2.49 5.833,2.646 0.313,0.156 10 false *b 5.5,2.771 5.813,2.927 0.313,0.156 10 false *b 1.271,2.417 1.583,2.573 0.313,0.156 10 false *d 3.188,2.917 3.583,3.083 0.396,0.167 10 false SST
*a String *b Molybdenum Grease Application Area
*c Place wrench here *d Center Nut
V113147

Turn - -


CAUTION:

Apply molybdenum grease to the bolt threads and the tip of SST.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part shown in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle LH.




Hide 45046 15.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 16.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 17.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51201 18.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C427905

Remove the bolts and separate the wiring harness clamp bracket from the front suspension crossmember sub-assembly.


b.
C427882C01
1,2.25 1.167,2.25 1.167,2.25 1.5,1.667 true 1.271,0.896 1.396,0.896 1.396,0.896 1.802,1.25 true 1.052,0.823 1.292,0.99 0.24,0.167 10 true *b 0.823,2.167 1.135,2.323 0.313,0.156 10 false *a
*a Transmission Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden block placement location


Using a transmission jack and a wooden block, support the engine assembly with transaxle.

CAUTION:
C427884

·

Support the engine assembly with transaxle until the front suspension crossmember sub-assembly is installed.

·

If the support is removed before the front suspension crossmember sub-assembly is installed, the engine assembly with transaxle may drop.




c.
C427885

Remove the bolt and separate the engine moving control rod.


d.

Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

C432278C01
3.083,1.438 3.375,1.635 3.375,1.635 3.542,1.635 true 1,1.583 3,1.583 3,1.583 3,1.083 true 2.729,1.583 2.729,1.115 true 2.021,1.583 2.021,1.25 true 1.615,1.583 1.615,1.302 true 3.583,1.542 3.896,1.698 0.313,0.156 10 false *a 0.792,1.479 1.104,1.635 0.313,0.156 10 false *b
*a Engine Lifter *b Attachment
V100155

Attachment placement location - -


CAUTION:
·
C320210

The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments to keep the front suspension crossmember sub-assembly level.



e.
C432279

Remove the 10 bolts and front suspension crossmember sub-assembly.


f.

Slowly lower the front suspension crossmember sub-assembly.

NOTICE:
·

When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.

·

Make sure that the front suspension crossmember sub-assembly dose not hit the protrusion of the reinforcement.




Hide 12363A 19.REMOVE ENGINE MOVING CONTROL ROD

a.
C427890

Remove the bolt and engine moving control rod from the front suspension crossmember sub-assembly.


Hide 48069 20.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C428575

Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48068 21.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 22.REMOVE STEERING LINK ASSEMBLY

Hide 48811 23.REMOVE FRONT STABILIZER BAR