Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P034031  Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal  


DESCRIPTION

Refer to DTC P034011.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P034011

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal No camshaft position sensor (for intake camshaft) signal for 5 seconds at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for intake camshaft) circuit

·

Camshaft position sensor (for intake camshaft)

·

Intake camshaft

·

ECM


Comes on DTC stored SAE: P0340

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P034011

MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor (for intake camshaft) despite the camshaft rotating, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor (for intake camshaft)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P034031.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [A] through [B] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D7-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
D7-1 (VVI+) - Body ground Ignition switch ON 3.0 to 5.0 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-3 (VC) - D7-1 (VVI+) Ignition switch off 1.425 to 1.575 kΩ
D7-2 (VVI-) - Body ground Always Below 1 Ω



Post-procedure1

f.

None.


Result:
Proceed to
OK
NG



OK

2.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

NG

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
A316078C01
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


Pre-procedure1

a.

None.


Procedure1

b.

Visually check the camshaft position sensor (for intake camshaft) for damage.


c.

Check the camshaft position sensor (for intake camshaft) installation condition.

OK:

The camshaft position sensor (for intake camshaft) does not have any damage and is installed properly.



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

3.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

NG

REPLACE INTAKE CAMSHAFT

Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the intake camshaft.



4.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)

Pre-procedure1

a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-1 (VVI+) - D51-90 (VV1+) Always Below 1 Ω
D7-2 (VVI-) - D51-89 (VV1-) Always Below 1 Ω
D7-3 (VC) - D51-88 (VCV1) Always Below 1 Ω
D7-1 (VVI+) or D51-90 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
D7-2 (VVI-) or D51-89 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
D7-3 (VC) or D51-88 (VCV1) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR