Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM J

M15A-FKS ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to IGP of the ECM. When the transistor in the MREL circuit operates, current flows from the battery to ground through the drive circuit of the EFI-MAIN NO. 1 relay, thus operating the relay which supplies power to the +B and +B2 terminals of the ECM.

WIRING DIAGRAM

A460177E01
0.552,4.813 1.469,5.01 0.917,0.198 10 false Battery 0.406,3.49 1.646,3.677 1.24,0.188 10 false BATT-MAIN NO.1 1.885,2.156 2.802,2.354 0.917,0.198 10 false IGP-MAIN 0.75,0.656 1.667,0.854 0.917,0.198 10 false AM1 5.781,3.646 6.698,3.844 0.917,0.198 10 false MREL 5.844,2.865 6.76,3.063 0.917,0.198 10 false +B 5.844,3.292 6.76,3.49 0.917,0.198 10 false +B2 5.844,1.875 6.76,2.073 0.917,0.198 10 false IGP 6.177,4.844 6.604,5.083 0.427,0.24 10 false ECM 6.198,4.667 6.625,4.854 0.427,0.188 10 false A54 4.823,2.552 5.448,2.802 0.625,0.25 10 false EFI NO.2 4.844,2.292 5.083,2.5 0.24,0.208 10 false 1 5.094,2.302 5.333,2.51 0.24,0.208 10 false 2 4.917,2.115 5.833,2.313 0.917,0.198 10 false INJ 5.656,2.771 5.896,2.979 0.24,0.208 10 false 9 5.583,3.219 5.823,3.427 0.24,0.208 10 false 35 5.563,3.646 5.802,3.854 0.24,0.208 10 false 15 5.854,4.25 6.771,4.448 0.917,0.198 10 false E1 5.563,4.167 5.802,4.375 0.24,0.208 10 false 10 5.635,1.875 5.875,2.083 0.24,0.208 10 false 2 3.313,4.042 4.646,4.365 1.333,0.323 10 false EFI-MAIN NO.1 4.083,3.646 4.323,3.854 0.24,0.208 10 false 1 4.083,3.198 4.323,3.406 0.24,0.208 10 false 3 3.281,3.646 3.521,3.854 0.24,0.208 10 false 2 3.292,3.208 3.531,3.417 0.24,0.208 10 false 5 1.76,3.49 3.094,3.813 1.333,0.323 10 false EFI-MAIN NO.1 3.656,2.708 4.573,2.906 0.917,0.198 10 false IGP 4.083,2.271 4.323,2.479 0.24,0.208 10 false 1 3.271,2.292 3.51,2.5 0.24,0.208 10 false 2 4.094,1.875 4.333,2.083 0.24,0.208 10 false 5 3.281,1.875 3.521,2.083 0.24,0.208 10 false 3 0.406,1.302 1.49,1.573 1.083,0.271 10 false INP STD NO.1-3 1.615,1.063 3.563,1.375 1.948,0.313 10 false Ignition Switch Assembly*2 1.646,0.875 2.563,1.073 0.917,0.198 10 false H54 1.51,0.365 1.75,0.573 0.24,0.208 10 false 7 2.729,0.354 2.969,0.563 0.24,0.208 10 false 8 3.375,0.365 3.615,0.573 0.24,0.208 10 false *2 4.99,0.385 5.229,0.594 0.24,0.208 10 false *1 5.333,0.823 6.25,1.021 0.917,0.198 10 false H45 5.292,1 7.115,1.552 1.823,0.552 10 false Certification ECU (Smart Key ECU Assembly)*1 5.823,0.479 6.74,0.677 0.917,0.198 10 false IGPD 5.49,0.365 5.729,0.573 0.24,0.208 10 false 24 1.719,4.927 4.719,5.188 3,0.26 10 false *1: w/ Entry and Start System 1.698,5.271 4.698,5.531 3,0.26 10 false *2: w/o Entry and Start System 2.396,0.354 2.635,0.563 0.24,0.208 10 false IG1 1.708,0.354 2.073,0.563 0.365,0.208 10 false AM1 6.375,3.729 6.927,3.896 0.552,0.167 10 false IC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-10 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IGP TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGP TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-2 (IGP) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI-MAIN NO. 1 RELAY

NG

6.INSPECT IGP RELAY
3.INSPECT EFI-MAIN NO. 1 RELAY

OK

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPLACE EFI-MAIN NO. 1 RELAY

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Remove the A/F HTR relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay from the No. 1 engine room relay block and junction block assembly.

HINT:

Remove the A/F HTR relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 1 relay) - A54-15 (MREL) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) - A54-9 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) - A54-35 (+B2) Always Below 1 Ω
1 (EFI-MAIN NO. 1 relay) or A54-15 (MREL) - Body ground and other terminals Always 10 kΩ or higher
3 (EFI-MAIN NO. 1 relay), A54-9 (+B) or A54-35 (+B2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)
A459385C02
0.073,0.042 0.385,0.198 0.313,0.156 10 false *1 1.573,2.156 1.885,2.313 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 1 Relay


a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V
2 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 1 RELAY)

6.INSPECT IGP RELAY

OK

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - ECM)

NG

REPLACE IGP RELAY

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - ECM)
a.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - A54-2 (IGP) Always Below 1 Ω
5 (IGP relay) or A54-2 (IGP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGP RELAY)
A459386C02
0.146,0.083 0.458,0.281 0.313,0.198 10 false *1 1.125,2.125 1.438,2.323 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 IGP Relay


a.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (IGP relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IG2 NO. 1 RELAY)

9.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)
a.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGP relay) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IGP RELAY)

B

11.INSPECT IGNITION SWITCH ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IGP RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-24 (IGPD) - 1 (IGP relay) Always Below 1 Ω
H45-24 (IGPD) or 1 (IGP relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT IGNITION SWITCH ASSEMBLY

OK

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IGP RELAY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IGP RELAY)
a.

Disconnect the ignition switch assembly connector.


b.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-8 (IG1) - 1 (IGP relay) Always Below 1 Ω
H54-8 (IG1) or 1 (IGP relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR