Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P107A11  Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Ground  


DESCRIPTION

A406948E18
0.083,0.125 7.031,0.448 6.948,0.323 10 false Characteristics of Fuel Pressure Sensor: 2.01,1.229 2.917,1.552 0.906,0.323 10 false Voltage (V) 2.073,1.708 2.49,2 0.417,0.292 10 false 4.5 2.01,3.208 2.438,3.573 0.427,0.365 10 false 0.75 2.531,3.521 2.802,3.792 0.271,0.271 10 false 0 4.833,3.51 5.229,3.813 0.396,0.302 10 false 750 3.042,3.917 4.646,4.26 1.604,0.344 10 false Fuel Pressure (kPa)

The fuel pressure sensor replaces the fuel pressure with electrical signals and outputs them to the ECM. The ECM controls the optimal fuel pressure for the operation conditions to reduce the fuel pump power consumption and improve fuel economy.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P107A11 Fuel Rail Pressure Sensor (Low) Circuit Short to Ground The fuel pressure sensor output voltage is less than 0.43 V for 3 seconds or more (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor

·

ECM


Comes on DTC stored SAE Code: P107C

HINT:

When this DTC is output, check the fuel pressure in the Data List. Enter the following menus: Powertrain / Engine / Data List / Low Fuel Pressure Sensor.

DTC No. Low Fuel Pressure Sensor Malfunction
P107A11 Approximately 0 kPag
·

Short to ground in PFL circuit

·

Short in PFL to EPFL circuit

·

Open in VCPF circuit



If the Data List values are normal, it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


MONITOR DESCRIPTION

This DTC is stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short in the sensor circuit.

MONITOR STRATEGY

Required Sensors/Components Fuel pressure sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine.

10.

Idle the engine for 10 seconds or more [A].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P107A11.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [B] again.




WIRING DIAGRAM

A403505E92
0.396,2.885 0.854,3.083 0.458,0.198 10 false E4 0.396,3.052 1.979,3.667 1.583,0.615 10 false Fuel Pressure Sensor 1.406,1.021 1.719,1.219 0.313,0.198 10 false VC 1.729,0.906 1.885,1.104 0.156,0.198 10 false 1 1.333,1.719 1.792,1.917 0.458,0.198 10 false PFL 1.729,1.604 1.885,1.802 0.156,0.198 10 false 2 1.417,2.49 1.729,2.688 0.313,0.198 10 false E2 1.74,2.385 1.896,2.583 0.156,0.198 10 false 3 4.281,0.927 4.594,1.125 0.313,0.198 10 false 130 4.292,1.594 4.75,1.792 0.458,0.198 10 false 129 4.292,2.406 4.604,2.604 0.313,0.198 10 false 128 4.604,0.917 5.167,1.208 0.563,0.292 10 false VCPF 4.646,1.604 5.104,1.802 0.458,0.198 10 false PFL 4.625,2.385 5.24,2.583 0.615,0.198 10 false EPFL 5.604,0.688 6.063,0.885 0.458,0.198 10 false 5 V 5.323,3.094 5.781,3.292 0.458,0.198 10 false D52 5.323,3.25 5.75,3.531 0.427,0.281 10 false ECM 5.302,1.417 5.917,1.615 0.615,0.198 10 false 180 kΩ

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the fuel E4 pressure sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E4-1 (VC) - E4-3 (E2) Ignition switch ON 4.75 to 5.25 V
E4-2 (PFL) - E4-3 (E2) Ignition switch ON 4.75 to 5.25 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E4-1 (VC) - E4-2 (PFL) Ignition switch off 171 to 189 kΩ



Post-procedure1

f.

None.


Result:
Proceed to
OK
NG



OK

REPLACE FUEL PRESSURE SENSOR

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PRESSURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



NG

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

Pre-procedure1

a.

Disconnect the E4 fuel pressure sensor connector.


b.

Disconnect the D52 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E4-1 (VC) - D52-130 (VCPF) Always Below 1 Ω
E4-2 (PFL) or D52-129 (PFL) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR