Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM J

M15A-FXE ENGINE CONTROL  SFI SYSTEM  Ignition Circuit  


DESCRIPTION

A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark from the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

WIRING DIAGRAM

A457719E01
1.146,0.625 1.333,0.802 0.188,0.177 10 false 3 1.146,1.094 1.271,1.26 0.125,0.167 10 false 2 1.99,0.635 2.115,0.802 0.125,0.167 10 false 5 1.979,1.083 2.104,1.25 0.125,0.167 10 false 1 1.49,1.5 2.167,1.688 0.677,0.188 10 false IGP 0.396,4.115 1.052,4.313 0.656,0.198 10 false IGP-MAIN 0.552,3.417 2.688,3.813 2.135,0.396 10 false Certification ECU (Smart Key ECU Assembly)*1 0.427,4.823 0.854,5.219 0.427,0.396 10 false BATT-MAIN 0.594,5.76 1.729,6.031 1.135,0.271 10 false Auxiliary Battery 2.729,0.917 2.979,1.104 0.25,0.188 10 false INJ 3.75,0.635 3.875,0.802 0.125,0.167 10 false 1 3.76,0.948 3.885,1.115 0.125,0.167 10 false 3 4.958,0.635 5.083,0.802 0.125,0.167 10 false 2 3.948,0.75 4.198,0.938 0.25,0.188 10 false +B 3.958,1.063 4.292,1.25 0.333,0.188 10 false GND 4.552,0.75 4.885,0.927 0.333,0.177 10 false IGT1 3.427,1.479 3.76,1.667 0.333,0.188 10 false D1 3.438,1.656 5.833,1.938 2.396,0.281 10 false Ignition Coil Assembly (No. 1 Cylinder) 3.76,2.25 3.885,2.417 0.125,0.167 10 false 1 3.76,2.563 3.885,2.729 0.125,0.167 10 false 3 4.958,2.229 5.083,2.396 0.125,0.167 10 false 2 3.948,2.365 4.198,2.552 0.25,0.188 10 false +B 3.948,2.688 4.281,2.875 0.333,0.188 10 false GND 4.552,2.365 4.885,2.542 0.333,0.177 10 false IGT2 3.448,3.083 3.781,3.271 0.333,0.188 10 false D2 3.438,3.25 5.917,3.677 2.479,0.427 10 false Ignition Coil Assembly (No. 2 Cylinder) 3.75,4.01 3.875,4.177 0.125,0.167 10 false 1 3.75,4.417 3.875,4.583 0.125,0.167 10 false 3 4.969,4.021 5.094,4.188 0.125,0.167 10 false 2 3.958,4.125 4.208,4.313 0.25,0.188 10 false +B 3.958,4.531 4.292,4.719 0.333,0.188 10 false GND 4.563,4.125 4.896,4.302 0.333,0.177 10 false IGT3 3.5,4.865 3.833,5.052 0.333,0.188 10 false D3 3.51,5.021 5.906,5.281 2.396,0.26 10 false Ignition Coil Assembly (No. 3 Cylinder) 6.292,4.781 6.625,4.969 0.333,0.188 10 false D52 6.281,4.948 6.635,5.135 0.354,0.188 10 false ECM 5.625,0.625 5.802,0.802 0.177,0.177 10 false 75 5.875,0.594 6.208,0.771 0.333,0.177 10 false IGT1 5.875,2.208 6.208,2.385 0.333,0.177 10 false IGT2 5.865,3.938 6.198,4.115 0.333,0.177 10 false IGT3 5.615,2.25 5.792,2.427 0.177,0.177 10 false 74 5.615,3.99 5.792,4.167 0.177,0.177 10 false 73 0.542,3.25 1.219,3.438 0.677,0.188 10 false H45 1.698,2.865 2.375,3.052 0.677,0.188 10 false IGPD 2.135,2.74 2.354,2.948 0.219,0.208 10 false 24 2.219,4.177 2.438,4.385 0.219,0.208 10 false 8 2.292,2.979 2.51,3.188 0.219,0.208 10 false *1 2.313,4.406 2.531,4.615 0.219,0.208 10 false *2 1.031,4.667 1.708,4.854 0.677,0.188 10 false H54 1.021,4.844 2.885,5.427 1.865,0.583 10 false Ignition Switch Assembly*2 1.875,4.292 2.552,4.479 0.677,0.188 10 false IG1 3.219,6.417 5.76,6.844 2.542,0.427 10 false *2: w/o Entry and Start System 3.219,6.073 5.76,6.5 2.542,0.427 10 false *1: w/ Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Perform a spark test before proceeding. If there is no spark for any cylinder, inspect this circuit.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.

Disconnect the D1, D2 and D3 ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D1-1 (+B) - D1-3 (GND) Ignition switch ON 11 to 14 V
D2-1 (+B) - D2-3 (GND) Ignition switch ON 11 to 14 V
D3-1 (+B) - D3-3 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the D1, D2 and D3 ignition coil assembly connectors.


b.

Disconnect the D52 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (IGT1) - D52-75 (IGT1) Always Below 1 Ω
D2-2 (IGT2) - D52-74 (IGT2) Always Below 1 Ω
D3-2 (IGT3) - D52-73 (IGT3) Always Below 1 Ω
D1-2 (IGT1) or D52-75 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
D2-2 (IGT2) or D52-74 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
D3-2 (IGT3) or D52-73 (IGT3) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the D1, D2 and D3 ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-3 (GND) - Body ground Always Below 1 Ω
D2-3 (GND) - Body ground Always Below 1 Ω
D3-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - IGP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - IGP RELAY)
a.

Remove the IGP relay from the No. 1 engine room relay block.


b.

Disconnect the D1, D2 and D3 ignition coil assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - D1-1 (+B) Always Below 1 Ω
5 (IGP relay) - D2-1 (+B) Always Below 1 Ω
5 (IGP relay) - D3-1 (+B) Always Below 1 Ω
5 (IGP relay) or D1-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP relay) or D2-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP relay) or D3-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR