Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P062712  Fuel Pump "A" Control Circuit Short to Battery  


DESCRIPTION

The fuel pump control ECU performs PWM (Pulse Width Modulation) control to control the fuel pump speed steplessly over a wide range.

The fuel pump control ECU controls the speed of the fuel pump by switching the current of FPU, FPV and FPW based on operation signals output from the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P062712 Fuel Pump "A" Control Circuit Short to Battery When the fuel pump control ECU operation duty ratio is 3 to 65%, the FPC terminal voltage is at a certain value or more for 3 seconds or more (1 trip detection logic).
·

Short in fuel pump control ECU circuit

·

Fuel pump control ECU

·

ECM


Does not come on DTC stored SAE Code: P0629

Related Data List
DTC No. Data List
P062712 Fuel Pump Control Duty Ratio

MONITOR DESCRIPTION

The ECM monitors the fuel pump control ECU operation signals.

When the output duty ratio of the operation signal from the ECM is 3 to 65% and the FPC terminal voltage is a certain value or more for 3 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Fuel pump control ECU
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and wait 10 seconds or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P062712.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, run the engine at an engine speed of 2500 rpm or more for 10 seconds or more and check the DTC judgment result again.




WIRING DIAGRAM

A404863E25
6.073,0.552 6.625,0.833 0.552,0.281 10 false MREL 5.813,0.531 6.115,0.823 0.302,0.292 10 false 11 2.823,0.531 3.052,0.833 0.229,0.302 10 false 2 2.031,0.521 2.188,0.719 0.156,0.198 10 false 1 2.823,1.146 2.979,1.344 0.156,0.198 10 false 3 2.042,1.146 2.198,1.344 0.156,0.198 10 false 5 2.052,1.646 3.385,1.969 1.333,0.323 10 false EFI-MAIN NO. 1 0.667,1.479 1.823,1.76 1.156,0.281 10 false EFI-MAIN NO. 1 1.615,2.75 2.771,3.042 1.156,0.292 10 false EFI-MAIN NO. 2 5.344,2 5.5,2.198 0.156,0.198 10 false 2 4.552,2.01 4.708,2.208 0.156,0.198 10 false 1 5.354,2.49 5.51,2.688 0.156,0.198 10 false 3 4.563,2.49 4.719,2.688 0.156,0.198 10 false 5 4.49,2.948 5.688,3.26 1.198,0.313 10 false EFI-MAIN NO. 2 0.417,4.094 0.833,4.5 0.417,0.406 10 false BATT-MAIN 0.583,5.24 1.146,5.729 0.563,0.49 10 false Auxiliary Battery 3.073,6.458 4.01,6.781 0.938,0.323 10 false *1: Shielded 0.906,6.021 1.365,6.219 0.458,0.198 10 false O21 1.188,6.021 2.396,6.49 1.208,0.469 10 false Fuel Pump 1.531,3.906 2.146,4.104 0.615,0.198 10 false BLPU 1.99,3.792 2.146,3.99 0.156,0.198 10 false 3 1.521,4.458 2.135,4.656 0.615,0.198 10 false BLPV 1.979,4.344 2.135,4.542 0.156,0.198 10 false 4 1.51,4.99 2.125,5.188 0.615,0.198 10 false BLPW 1.979,4.885 2.135,5.083 0.156,0.198 10 false 2 1.552,5.521 2.167,5.719 0.615,0.198 10 false BLPE 1.979,5.396 2.135,5.594 0.156,0.198 10 false 1 2.573,5.667 2.896,5.917 0.323,0.25 10 false *1 3.083,3.74 3.24,3.938 0.156,0.198 10 false 2 3.323,3.906 3.781,4.104 0.458,0.198 10 false FPU 3.083,4.281 3.24,4.479 0.156,0.198 10 false 3 3.323,4.448 3.781,4.646 0.458,0.198 10 false FPV 3.073,4.802 3.229,5 0.156,0.198 10 false 4 3.021,5.521 3.479,5.719 0.458,0.198 10 false O1 3.073,5.344 3.229,5.542 0.156,0.198 10 false 1 3.333,5.51 3.792,5.708 0.458,0.198 10 false FPG 3.333,4.979 3.792,5.177 0.458,0.198 10 false FPW 4.875,3.938 5.031,4.135 0.156,0.198 10 false 1 4.552,4.115 4.865,4.313 0.313,0.198 10 false +B 4.885,4.5 5.042,4.698 0.156,0.198 10 false 2 4.427,4.563 4.875,4.823 0.448,0.26 10 false FPC 4.823,5.552 5.281,5.75 0.458,0.198 10 false O2 4.875,5.375 5.031,5.573 0.156,0.198 10 false 3 4.438,5.542 4.896,5.74 0.458,0.198 10 false GND 3.281,6.042 4.948,6.396 1.667,0.354 10 false Fuel Pump Control ECU 5.813,4.573 6.135,4.813 0.323,0.24 10 false 20 6.073,4.573 6.531,4.771 0.458,0.198 10 false FPC 6.156,6.042 6.583,6.323 0.427,0.281 10 false A53 6.542,6.042 7,6.24 0.458,0.198 10 false ECM 6.635,0.594 6.844,0.792 0.208,0.198 10 false IC 4,6.448 5.948,6.75 1.948,0.302 10 false *2: Diagnosis Output Circuit 3.906,4.948 4.229,5.271 0.323,0.323 10 false *2 3.042,4.979 3.5,5.177 0.458,0.198 10 false O1 3.042,4.448 3.5,4.646 0.458,0.198 10 false O1 3.031,3.906 3.49,4.104 0.458,0.198 10 false O1 4.844,4.677 5.302,4.875 0.458,0.198 10 false O2 4.844,4.125 5.302,4.323 0.458,0.198 10 false O2

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ECM (CHECK FOR SHORT)

Pre-procedure1

a.

Disconnect the O2 fuel pump control ECU connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O2-2 (FPC) - Body ground Ignition switch ON Below 1 V



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP CONTROL ECU

NG

2.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)

Pre-procedure1

a.

Disconnect the O2 fuel pump control ECU connector.


b.

Disconnect the A53 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-2 (FPC) or A53-20 (FPC) - Other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR