Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P052012  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery  P052014  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open  


DESCRIPTION

A107720E70
0.135,0.708 1.406,1 1.271,0.292 10 false Voltage (V) 0.344,1.031 0.573,1.24 0.229,0.208 10 false 4.1 0.333,2.156 0.563,2.365 0.229,0.208 10 false 0.6 0.74,2.417 0.854,2.625 0.115,0.208 10 false 0 2.542,2.417 2.948,2.688 0.406,0.271 10 false 1.0 1.198,2.688 2.615,2.927 1.417,0.24 10 false Oil Pressure (MPa) 0.427,0.177 3.01,0.646 2.583,0.469 10 false Characteristics of Oil Pressure Sensor:

Variable oil pump control uses the oil pressure control valve assembly, engine oil pressure and temperature sensor and ECM to optimize the oil pressure and oil volume required by each component to reduce friction by monitoring the engine temperature and engine speed. The engine oil pressure and temperature sensor utilizes a semiconductor type pressure sensor that changes resistance in accordance with changes in pressure. An internal electrical signal that varies with the change in resistance is amplified and sent to the ECM as the engine oil pressure signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P052012 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery The engine oil pressure and temperature sensor output voltage is higher than 4.495 V for 5 seconds or more (1 trip detection logic).
·

Open or short in engine oil pressure and temperature sensor circuit

·

Engine oil pressure and temperature sensor

·

ECM


Comes on DTC stored SAE Code: P0523
P052014 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open The engine oil pressure and temperature sensor output voltage is less than 0.159 V for 5 seconds or more (1 trip detection logic).
·

Open or short in engine oil pressure and temperature sensor circuit

·

Engine oil pressure and temperature sensor

·

ECM


Comes on DTC stored SAE Code: P0522

Related Data List
DTC No. Data List
P052012 Engine Oil Pressure
P052014

MONITOR DESCRIPTION

The ECM calculates the engine oil pressure based on the output voltage of the engine oil pressure and temperature sensor. If the signal output from the engine oil pressure and temperature sensor is outside of the specified range, the MIL is illuminated and a DTC is stored.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Wait 10 seconds or more [B].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P052012 or P052014.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions




HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [A] through [C] again.



WIRING DIAGRAM

A402979E63
1.01,1.719 1.542,1.927 0.531,0.208 10 false POUT 1.198,1.031 1.729,1.24 0.531,0.208 10 false VC 1.094,2.5 1.625,2.708 0.531,0.208 10 false GND 4.75,0.938 5.281,1.146 0.531,0.208 10 false VCPE 4.417,0.938 4.948,1.146 0.531,0.208 10 false 124 4.479,2.396 5.01,2.604 0.531,0.208 10 false 92 4.417,1.625 4.948,1.833 0.531,0.208 10 false 123 4.927,2.125 5.458,2.333 0.531,0.208 10 false 200 kΩ 4.75,2.396 5.281,2.604 0.531,0.208 10 false EPEO 4.75,1.625 5.281,1.833 0.531,0.208 10 false PEO 5.604,3.26 6.135,3.469 0.531,0.208 10 false ECM 5.604,3.104 6.135,3.313 0.531,0.208 10 false D52 0.24,2.896 0.771,3.104 0.531,0.208 10 false D32 0.24,3.063 4.25,3.542 4.01,0.479 10 false Engine Oil Pressure and Temperature Sensor 1.5,0.927 2.031,1.135 0.531,0.208 10 false 3 1.51,1.615 2.042,1.823 0.531,0.208 10 false 1 1.51,2.396 2.042,2.604 0.531,0.208 10 false 2 6.115,0.688 6.646,0.896 0.531,0.208 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the D32 engine oil pressure and temperature sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D32-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
D32-1 (POUT) - Body ground Ignition switch ON Below 0.1 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
D32-1 (POUT) - D32-2 (GND) Ignition switch off 190 to 210 kΩ
D32-2 (GND) - Body ground Ignition switch off Below 1 Ω



Post-procedure1

f.

None.


Result:
Proceed to
OK
NG



OK

REPLACE ENGINE OIL PRESSURE AND TEMPERATURE SENSOR

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR - ECM)

Pre-procedure1

a.

Disconnect the D32 engine oil pressure and temperature sensor connector.


b.

Disconnect the D52 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D32-2 (GND) - D52-92 (EPEO) Always Below 1 Ω
D32-1 (POUT) - D52-123 (PEO) Always Below 1 Ω
D32-3 (VC) - D52-124 (VCPE) Always Below 1 Ω
D32-2 (GND) or D52-92 (EPEO) - Body ground and other terminals Always 10 kΩ or higher
D32-1 (POUT) or D52-123 (PEO) - Body ground and other terminals Always 10 kΩ or higher
D32-3 (VC) or D52-124 (VCPE) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR