Home › Power Source / Network › M15A-FXE (BATTERY / CHARGING) › CHARGING SYSTEM
RM36W0E _57 Power Source / Network _087764 M15A-FXE BATTERY / CHARGING _0419405 CHARGING SYSTEM C

M15A-FXE BATTERY / CHARGING  CHARGING SYSTEM  P162B87  Lost Communication with Battery Monitor Module Missing Message  


DESCRIPTION

The hybrid vehicle control ECU communicates with the battery state sensor assembly via LIN communication. If a LIN communication error is detected, the hybrid vehicle control ECU stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P162B87 Lost Communication with Battery Monitor Module Missing Message Battery state sensor assembly or hybrid vehicle control ECU communication stops for approximately 17 minutes or more with the ignition switch to ON
(1 trip detection logic)
·

Wire harness or connector

·

Battery state sensor assembly

·

Hybrid vehicle control ECU


Charge warning light:
Does not come on
DTC stored SAE Code: P162B

WIRING DIAGRAM

A409155E20
0.906,2.302 1.979,2.51 1.073,0.208 10 false Auxiliary Battery 0.792,3.302 2.448,3.5 1.656,0.198 10 false : LIN Communication Line 1.125,0.813 2.052,1.021 0.927,0.208 10 false BATT-S NO. 1 2.271,1.135 2.729,1.333 0.458,0.198 10 false O68 2.25,1.281 4.542,1.479 2.292,0.198 10 false Battery State Sensor Assembly 2.323,0.656 2.635,0.854 0.313,0.198 10 false +B 3.406,0.667 3.719,0.865 0.313,0.198 10 false LIN 2.146,0.552 2.302,0.75 0.156,0.198 10 false 3 3.698,0.51 3.854,0.708 0.156,0.198 10 false 2 5.229,0.5 5.542,0.698 0.313,0.198 10 false 28 5.49,0.667 6.104,0.865 0.615,0.198 10 false LIN3 5.24,2.875 5.698,3.073 0.458,0.198 10 false A68 5.229,3.01 7.063,3.323 1.833,0.313 10 false Hybrid Vehicle Control ECU 2.271,2.615 2.729,2.813 0.458,0.198 10 false D75 3.719,1.99 4.177,2.188 0.458,0.198 10 false 3 3.26,2.146 3.719,2.344 0.458,0.198 10 false DOUT 2.26,2.771 4.542,3.01 2.281,0.24 10 false Compressor with Motor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION
a.

Check installation condition of the battery state sensor assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



Procedure1

d.
A456515C03
1.51,0.135 1.938,0.438 0.427,0.302 2.219,1.688 1.885,1.146 true 1.125,1.667 1.49,1.125 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 2.26,1.708 2.698,1.927 0.438,0.219 10 false +B 1.604,0.219 2.063,0.417 0.458,0.198 10 false O68 0.802,1.708 1.24,1.927 0.438,0.219 10 false RBAT
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O68-3 (+B) - Body ground Ignition switch off 11 to 14 V



Post-procedure1

e.

None.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY STATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY STATE SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the A68 hybrid vehicle control ECU connector.


b.

Disconnect the O68 battery state sensor assembly connector.


c.

Disconnect the D75 compressor with motor assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A68-28 (LIN3) - O68-2 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
O68-2 (LIN), A68-28 (LIN3) or D75-3 (DOUT) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None.


Result:
Proceed to
OK
NG



OK

4.CLEAR DTCS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTCS

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs, and note down any DTCs that are output.

Click herePower Source / Network>M15A-FXE (BATTERY / CHARGING)>CHARGING SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397

c.

Clear the DTCs.

Click herePower Source / Network>M15A-FXE (BATTERY / CHARGING)>CHARGING SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Clear DTCs
50002 397

Post-procedure1

d.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTCS (AIR CONDITIONING SYSTEM)
5.CLEAR DTCS (AIR CONDITIONING SYSTEM)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs, and note down any DTCs that are output.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 450

c.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 450

Post-procedure1

d.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS
6.CHECK FOR DTCS

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and wait for 17 minutes or more.


Procedure1

b.

Check for DTCs.

Click herePower Source / Network>M15A-FXE (BATTERY / CHARGING)>CHARGING SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397

Post-procedure1

c.

None.


Result:
Result Proceed to
DTC P162B87 is output. A
DTCs are not output. B



A

7.CHECK FOR DTCS (AIR CONDITIONING SYSTEM)

B

7.CHECK FOR DTCS (AIR CONDITIONING SYSTEM)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs when the following conditions are met.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 450

Post-procedure1

c.

None.


Result:
Result Proceed to
DTC B149887 is output. A
DTCs are not output. B



A

B