Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0419699 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  U010087  Lost Communication with ECM/PCM "A" Missing Message  


DESCRIPTION

The TCM communicates with the ECM via CAN communication.

If a problem occurs in this communication, the TCM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U010087 Lost Communication with ECM/PCM "A" Missing Message No communication between the TCM and ECM for 1.25 seconds or more (1-trip detection logic)
·

Harness and connector

·

ECM

·

TCM


Comes on DTC stored SAE Code:
U0100

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Turn the ignition switch to ON and wait for 3 seconds or more.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: U010087.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C430035E02
6.115,4.188 6.573,4.385 0.458,0.198 10 false A54 6.115,4.365 6.573,4.563 0.458,0.198 10 false ECM 2.917,1.771 3.375,1.969 0.458,0.198 10 false D71 2.927,1.958 3.385,2.156 0.458,0.198 10 false TCM 3.094,0.542 3.708,0.74 0.615,0.198 10 false CAN+ 3.135,0.948 3.75,1.146 0.615,0.198 10 false CAN- 2.667,1.229 3.281,1.427 0.615,0.198 10 false E1 5.833,0.563 6.448,0.76 0.615,0.198 10 false CANP 5.833,0.948 6.448,1.146 0.615,0.198 10 false CANN 5.833,2.448 6.448,2.646 0.615,0.198 10 false +B 5.833,2.844 6.448,3.042 0.615,0.198 10 false +B2 5.844,3.25 6.458,3.448 0.615,0.198 10 false MREL 3.594,0.375 4.208,0.573 0.615,0.198 10 false 18 5.625,0.375 6.24,0.573 0.615,0.198 10 false 7 5.552,0.771 6.167,0.969 0.615,0.198 10 false 17 3.594,0.771 4.208,0.969 0.615,0.198 10 false 17 5.635,2.333 6.25,2.531 0.615,0.198 10 false 9 5.573,2.729 6.188,2.927 0.615,0.198 10 false 35 5.573,3.125 6.188,3.323 0.615,0.198 10 false 15 5.844,3.656 6.458,3.854 0.615,0.198 10 false E1 5.573,3.531 6.188,3.729 0.615,0.198 10 false 10 4.688,2.719 5.302,2.917 0.615,0.198 10 false 3 2.458,1.104 3.073,1.302 0.615,0.198 10 false 2 1.135,3.01 1.969,3.417 0.833,0.406 10 false BATT-MAIN NO. 1 3.792,3.583 5.021,3.781 1.229,0.198 10 false EFI-MAIN NO. 1 1.188,4.094 2.417,4.292 1.229,0.198 10 false Battery 0.531,5.156 4.198,5.354 3.667,0.198 10 false : CAN Communication Line 3.292,1.365 3.906,1.563 0.615,0.198 10 false +B 3.604,1.25 4.219,1.448 0.615,0.198 10 false 1 2.25,2.99 4.396,3.188 2.146,0.198 10 false EFI-MAIN NO. 1 3.99,1.521 5.365,1.719 1.375,0.198 10 false EFI NO. 5 3.823,2.729 4.438,2.927 0.615,0.198 10 false 5 3.823,3.125 4.438,3.323 0.615,0.198 10 false 2 4.677,3.125 5.292,3.323 0.615,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

Pre-procedure1

a.
A459385C02
0.073,0.042 0.385,0.198 0.313,0.156 10 false *1 1.573,2.156 1.885,2.313 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 1 Relay


Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V



Post-procedure1

c.

Install the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


Result:
Proceed to
OK
NG



OK

2.INSPECT EFI-MAIN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT EFI-MAIN NO. 1 RELAY

OK

3.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPLACE EFI-MAIN NO. 1 RELAY

3.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

Pre-procedure1

a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 1 relay) - A54-9 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) - A54-35 (+B2) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay), A54-9 (+B) or A54-35 (+B2) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

Connect the ECM connector.


e.

Install the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM
HINT:

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.PERFORM INITIALIZATION
5.PERFORM INITIALIZATION

NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373
HINT:

Write down the currently output DTCs before clearing them.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT (DTC U010087)
7.CHECK DTC OUTPUT (DTC U010087)

Pre-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the DTCs.

Powertrain > Transmission > Trouble Codes
50001 373

Post-procedure1

d.

None.


Result:
Result Proceed to
DTCs are not output A
U010087 is output B



A

END

B

8.REPLACE TCM
8.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT