Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Cooling System  


DESCRIPTION

The cause of the malfunction may be the cooling system.

Check whether the grille is blocked, whether coolant is leaking, the HV radiator fan operating condition and whether coolant has frozen.

Related Parts Check
Area Inspection
Grille blockage, coolant amount, coolant hoses, HV radiator fan Check for overheating due to hybrid cooling system malfunction.
Inverter coolant temperature sensor (built-in inverter) Check for temperature sensor malfunction.
Coolant freezing check Check freeze frame values to determine whether the hybrid coolant was frozen when the DTC was stored.

Related Data List
Data List
·

Inverter Coolant Water Temperature

·

Motor Inverter Temperature

·

Generator Inverter Calculated Temperature

·

Boosting Converter Temperature (Upper)

·

Boosting Converter Temperature (Lower)

·

Ambient Temperature

·

Inverter Water Pump Revolution



SYSTEM DESCRIPTION

The inverter converts the high-voltage direct current of the HV battery into alternating current for the generator (MG1) and motor (MG2). The inverter generates heat during the conversion process. Therefore, the inverter is cooled by a special cooling system consisting of the inverter water pump assembly, the cooling fan, and a radiator. This cooling system is independent of the engine cooling system. The hybrid vehicle control ECU monitors the inverter water pump assembly, cooling fan and cooling system, and detects malfunctions.

A458517C01
6.25,3.469 6.156,3.469 6.156,3.469 6.042,2.969 true 3.042,4.135 3.229,3.167 3.229,3.167 3.115,3.167 true 5.26,3.698 5.156,3.698 5.156,3.698 5.052,3.198 true 6.208,0.865 6.344,0.417 6.344,0.417 6.458,0.417 true 3.823,0.24 3.927,0.24 3.927,0.24 4.031,0.719 true 2.896,3.094 3.104,3.25 0.208,0.156 10 true *1 3.625,0.188 3.938,0.344 0.313,0.156 10 false *2 6.51,0.375 6.823,0.531 0.313,0.156 10 false *3 5.313,3.656 5.625,3.813 0.313,0.156 10 false *4 6.313,3.417 6.625,3.573 0.313,0.156 10 false *5
*1 Inverter Water Pump Assembly *2 Inverter Reserve Tank Assembly
*3 Inverter with Converter Assembly *4 Radiator Assembly (HV)
*5 Hybrid Vehicle Transaxle Assembly - -


WIRING DIAGRAM

A368421E42
5.625,5.542 7.104,6.083 1.479,0.542 10 false Hybrid Vehicle Control ECU 5.781,5.083 6.094,5.281 0.313,0.198 10 false E1 5.781,4.5 6.344,4.74 0.563,0.24 10 false MREL 5.781,3.01 6.344,3.25 0.563,0.24 10 false NIWP 5.781,1.51 6.344,1.75 0.563,0.24 10 false IWP 6.531,2.646 6.854,2.917 0.323,0.271 10 false +B 6.552,3.938 6.875,4.208 0.323,0.271 10 false +B 5.438,5.094 5.75,5.292 0.313,0.198 10 false H44 5.458,4.896 5.771,5.094 0.313,0.198 10 false 15 2.688,4.063 3,4.26 0.313,0.198 10 false A59 5.469,4.396 5.781,4.594 0.313,0.198 10 false 47 5.427,3.115 5.74,3.313 0.313,0.198 10 false A68 5.427,1.604 5.74,1.802 0.313,0.198 10 false A68 5.479,2.917 5.792,3.115 0.313,0.198 10 false 32 5.469,1.406 5.781,1.604 0.313,0.198 10 false 31 5.073,3.635 5.385,3.833 0.313,0.198 10 false 1 4.688,3.74 5.135,3.99 0.448,0.25 10 false GND 4.646,3 5.208,3.24 0.563,0.24 10 false NWP 5.073,3 5.385,3.198 0.313,0.198 10 false 2 4.646,1.51 5.208,1.75 0.563,0.24 10 false SWP 5.073,1.5 5.385,1.698 0.313,0.198 10 false 3 3.198,2.104 4.125,2.448 0.927,0.344 10 false Drive Circuit 2.708,1.198 3.271,1.438 0.563,0.24 10 false +BWP 2.552,1.198 2.865,1.396 0.313,0.198 10 false 4 2.198,1.167 2.51,1.365 0.313,0.198 10 false 2 1.865,1.167 2.177,1.365 0.313,0.198 10 false 1 1.115,2.01 1.948,2.198 0.833,0.188 10 false IGCT 1.854,1.438 2.781,1.781 0.927,0.344 10 false INV W/P 1.573,1.583 1.885,1.781 0.313,0.198 10 false 1 0.813,1.583 1.125,1.781 0.313,0.198 10 false 2 0.813,1.208 1.125,1.406 0.313,0.198 10 false 3 1.573,1.198 1.885,1.396 0.313,0.198 10 false 5 0.188,2.813 0.5,3.01 0.313,0.198 10 false 2 0.188,3.094 0.5,3.292 0.313,0.198 10 false 1 0.448,2.969 1.344,3.302 0.896,0.333 10 false IGCT-MAIN 0.063,4.969 1.698,5.458 1.635,0.49 10 false from Auxiliary Battery 0.292,5.854 4.469,6.219 4.177,0.365 10 false IWP : Inverter water pump assembly drive duty 0.281,6.313 4.75,6.708 4.469,0.396 10 false NIWP : Inverter water pump assembly speed signal 2.698,4.229 5.24,4.792 2.542,0.563 10 false Inverter Water Pump Assembly 5.427,4.615 5.74,4.813 0.313,0.198 10 false H44

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C04
1.563,0.708 1.813,0.417 true 1.844,0.302 2.156,0.5 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Make sure that the front side of the radiator grille is not blocked with anything.


b.

Ask the customer if the front side of the radiator grille was blocked with anything.


Result:
Result Proceed to
Not blocked A
Is/was blocked B


HINT:

If the radiator grille is blocked, the inverter coolant temperature will increase and this DTC may be stored.



A

2.CHECK QUANTITY OF HV COOLANT

B

IF EQUIPPED, EXPLAIN TO CUSTOMER THAT OPTIONAL COMPONENTS WILL BE REMOVED

2.CHECK QUANTITY OF HV COOLANT
a.

Check the HV coolant level in the inverter reserve tank.


b.

Check for HV coolant leaks.

Result:
Result Proceed to
No leaks are found and the HV coolant level in the inverter reserve tank assembly is above the low line A
No leaks are found and the HV coolant level in the inverter reserve tank assembly is below the low line B
HV coolant leaks are evident C


HINT:
·

After repairing the HV coolant leaks and adding coolant, perform the Active Tests "Activate the Inverter Water Pump" (Hybrid Control System) and "Control the Engine Cooling Fan" (Engine Control system) and make sure that there are no malfunctions.

·

If there are signs of coolant leakage around the connecting parts of a hose and the inverter with converter assembly, replace the hose with a new one.





A

3.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR COOLANT LEAK AND ADD COOLANT

3.CHECK COOLANT HOSE
a.

Check that the cooling system hoses are not kinked or clogged.

OK:

The cooling system hoses are not kinked or clogged.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN)

NG

REPAIR OR REPLACE COOLANT HOSE

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN)

Pre-procedure1

a.

None.


Procedure1

b.

Perform the "Control the Engine Cooling Fan" Active Test.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan
50004 372 26
Result:
Result Proceed to
Cooling fan operate A
Cooling fan does not operate B
Cooling fan do not stop



Post-procedure1

c.

Turn the ignition switch off.



A

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)

B

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
·

Make sure that the HV coolant level is above the low line of the inverter reserve tank.

·

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.



HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


Pre-procedure1

a.

None.


Procedure1

b.

According to the display on the GTS, perform the Active Test "Activate the Inverter Water Pump" and check the value of the Data List item "Inverter Water Pump Revolution".

Powertrain > Hybrid Control > Active Test
Active Test Display
Activate the Inverter Water Pump
Data List Display
Inverter Water Pump Revolution
50004 397 1 60
HINT:
·

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).

·

When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.




Post-procedure1

c.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Inverter Water Pump Revolution is 3200 rpm or more, and 8600 rpm or less A
The value of Inverter Water Pump Revolution is more than 8600 rpm, and less than 3200 rpm B



A

6.READ VALUE USING GTS (DATA LIST)

B

8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
6.READ VALUE USING GTS (DATA LIST)

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and wait for 1 minute with the engine stopped.


Procedure1

b.

Read the Data List with the engine stopped.

Powertrain > Hybrid Control > Data List
Tester Display
Generator Inverter Calculated Temperature
Motor Inverter Temperature
Boosting Converter Temperature (Upper)
Boosting Converter Temperature (Lower)
Inverter Coolant Water Temperature
50003 397 127,130,136,137,152
Result:
Result Proceed to
Other than below A
"Inverter Coolant Water Temperature" value is higher than the displayed temperature of any other Data List item by 20°C (68°F) or more B


HINT:

The lower limit temperature that can be displayed for "Generator Inverter Calculated Temperature", "Motor Inverter Temperature", "Boosting Converter Temperature (Upper)" and "Boosting Converter Temperature (Lower)" is 15°C (59°F). The lower limit temperature for "Inverter Coolant Water Temperature" is -40°C (-40°F). The "Inverter Coolant Water Temperature" value displayed on the GTS may be lower than the others, but this is not a malfunction.



Post-procedure1

c.

Turn the ignition switch off.



A

7.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

7.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

Pre-procedure1

a.

None.


Procedure1

b.

Check if the freeze frame data item Ambient Temperature is below the freezing temperature of the HV coolant.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Ambient Temperature value is above freezing temperature of the HV coolant A
Ambient Temperature value is below freezing temperature of the HV coolant B


HINT:
·

HV coolant (SLLC) with a 30% concentration freezes at -15°C (5°F) and HV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).

·

If the HV coolant freezes in the HV radiator or inverter water pump, the coolant temperature in the inverter with converter assembly rises because the HV coolant cannot circulate. As a result, a DTC may be stored.

·

A DTC is stored when the inverter water pump impeller cannot rotate due to freezing of the HV coolant.

·

If DTCs are output due to freezing of the LLC, the problem symptom cannot be reproduced. Check the LLC replacement history and whether the LLC was frozen based on the ambient temperature when the DTCs were stored.




Post-procedure1

c.

Turn the ignition switch off.



A

COOLING SYSTEM NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

B

8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
a.
A458518

Check the connector connections and contact pressure of the relevant terminals for the inverter water pump assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely, the terminals are not deformed or corroded and there are no contact problems.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

Pre-procedure1

a.

Disconnect the A68 hybrid vehicle control ECU connector.


b.

Disconnect the A59 inverter water pump assembly connector.


Procedure1

c.
A458567C01
1.51,2.615 1.927,2.865 0.417,0.25 1.458,0.323 1.875,0.573 0.417,0.25 1.75,2.094 1.979,1.552 true 1.74,4 1.833,3.615 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.25,2.677 0.563,2.833 0.313,0.156 10 false *b 1.542,2.125 2,2.323 0.458,0.198 10 false IWP 1.604,4.073 2.063,4.271 0.458,0.198 10 false SWP 1.563,0.385 2.021,0.583 0.458,0.198 10 false A68 1.615,2.677 2.073,2.875 0.458,0.198 10 false A59
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A68-31 (IWP) - A59-3 (SWP) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A68-31 (IWP) or A59-3 (SWP) - Body ground and other terminals Ignition switch off 10 kΩ or higher



Post-procedure1

d.

Reconnect the A59 inverter water pump assembly connector.


e.

Reconnect the A68 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


Pre-procedure1

a.
A458558C01
0.885,1 1.333,0.438 true 0.219,0.156 0.531,0.313 0.313,0.156 10 false *1 0.719,0.979 1.031,1.135 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 INV W/P Fuse


Remove the INV W/P fuse from No. 5 relay block assembly.


Procedure1

b.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Inverter Water Pump Revolution
50003 397 60

Post-procedure1

c.

Turn the ignition switch off.


d.

Install the INV W/P fuse.


Result:
Result Proceed to
The value of Inverter Water Pump Revolution is 200 rpm or less A
Inverter Water Pump Revolution is more than 200 rpm B



A

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

B

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

Pre-procedure1

a.

Disconnect the A68 hybrid vehicle control ECU connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

A458551C01
4.771,0.042 5.208,0.281 0.438,0.24 1.104,2.479 1.542,2.771 0.438,0.292 3.156,3.281 2.99,2.875 true 5.927,2.104 5.573,1.063 true 0.375,2.135 0.688,2.333 0.313,0.198 10 false *b 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 4.896,0.094 5.271,0.292 0.375,0.198 10 false H44 1.219,2.563 1.531,2.76 0.313,0.198 10 false A68 3.208,3.344 3.667,3.542 0.458,0.198 10 false IWP 5.948,2.146 6.406,2.344 0.458,0.198 10 false E1
*a Component with harness connected
(Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Standard Voltage:
Tester Connection Condition Specified Condition
A68-31 (IWP) - H44-15 (E1) Ignition switch ON 11 to 14 V


NOTICE:

Make sure to check for and clear DTCs after performing this inspection.



Post-procedure1

d.

Turn the ignition switch off.


e.

Reconnect the A68 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

13.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

NG

14.REPLACE INVERTER WATER PUMP ASSEMBLY
13.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

Pre-procedure1

a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below.


Procedure1

b.

Turn the ignition switch to ON.


c.

While turning the ignition switch to ON, check the waveform between the hybrid vehicle control ECU terminals.

A458550C09
4.708,0.271 5.188,0.552 0.479,0.281 2.49,0.271 2.969,0.552 0.479,0.281 2.042,2.417 2.521,1.51 true 5.958,2.438 5.552,1.396 true 0.271,0.167 0.583,0.323 0.313,0.156 10 false *a 2.615,0.354 2.927,0.51 0.313,0.156 10 false A68 5.99,2.427 6.302,2.583 0.313,0.156 10 false E1 4.844,0.344 5.156,0.5 0.313,0.156 10 false H44 1.813,2.438 2.125,2.594 0.313,0.156 10 false IWP
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Item Content
Terminal A68-31 (IWP) - H44-15 (E1)
Equipment Setting 5 V/DIV., 50 ms./DIV.
Condition Ignition switch ON

OK:

Waveform duty ratio is between 3% and 9%.



Post-procedure1

d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

14.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

14.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

15.ADD HV COOLANT AND PERFORM AIR BLEEDING
15.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

HINT:

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter)>REPLACEMENT


Result:
Proceed to
NEXT




NEXT

END