Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P056014  System Voltage (BATT) Circuit Short to Ground or Open  


DESCRIPTION

Auxiliary battery power is supplied to the BATT terminal of the hybrid vehicle control ECU in order to store DTCs and freeze frame data. Even if the ignition switch is turned off, back-up power is supplied.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P056014 System Voltage (BATT) Circuit Short to Ground or Open Malfunction in the hybrid vehicle control ECU back-up power source circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Fuse


Comes on Master Warning: Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

With ignition switch ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A425329E05
0.76,2.24 2.438,2.594 1.677,0.354 10 false Auxiliary Battery 0.604,1.521 1.979,1.719 1.375,0.198 10 false BATT-MAIN 1.708,1.281 2.813,1.458 1.104,0.177 10 false INP STD NO.1-3 3.354,1.313 4.375,1.563 1.021,0.25 10 false ECU-B NO. 2 5.677,1.125 6.448,1.323 0.771,0.198 10 false BATT 5.688,2.198 6.458,2.396 0.771,0.198 10 false E1 5.219,2.771 5.99,2.969 0.771,0.198 10 false H44 5.229,2.927 7.063,3.344 1.833,0.417 10 false Hybrid Vehicle Control ECU 1.979,1 2.25,1.167 0.271,0.167 10 false 1 2.208,1 2.479,1.167 0.271,0.167 10 false 2 3.573,1 3.844,1.167 0.271,0.167 10 false 1 3.823,1 4.094,1.167 0.271,0.167 10 false 2 5.385,1 5.656,1.167 0.271,0.167 10 false 13 5.406,2.083 5.677,2.25 0.271,0.167 10 false 15

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
a.
A458477

Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ECU-B NO. 2 FUSE)

NG

CONNECT SECURELY

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ECU-B NO. 2 FUSE)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

A458550C01
4.688,0.26 5.125,0.542 0.438,0.281 3.677,2.365 4.021,1.292 true 5.854,2.344 5.542,1.385 true 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 5.865,2.385 6.177,2.583 0.313,0.198 10 false E1 3.49,2.385 3.938,2.656 0.448,0.271 10 false BATT 4.802,0.333 5.135,0.583 0.333,0.25 10 false H44
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H44-13 (BATT) - H44-15 (E1) Ignition switch off 11 to 14 V



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK FUSE (ECU-B NO. 2)
3.CHECK FUSE (ECU-B NO. 2)

Pre-procedure1

a.
A458555C01
1.938,1.49 2.146,1.042 2.146,1.042 2.25,1.042 true 0.219,0.177 0.531,0.333 0.313,0.156 10 false *1 2.313,0.979 2.625,1.135 0.313,0.156 10 false *2
*1 Power Distribution Box Assembly
*2 ECU-B NO. 2 Fuse


Remove the ECU-B NO. 2 fuse from the power distribution box assembly.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-B NO. 2 fuse Always Below 1 Ω



Post-procedure1

c.

Reinstall the ECU-B NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE FUSE (ECU-B NO. 2)