Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P253012  IG2 Signal Circuit Short to Auxiliary Battery  


DESCRIPTION

w/ Smart Key System:

The hybrid vehicle control ECU compares the IGP signal to the IG control status signal sent from the certification ECU (smart key ECU assembly) to detect a stuck on malfunction of the IGP signal.


w/o Smart Key System:

The hybrid vehicle control ECU compares the IGP signal to the IG switch signal sent from the main body ECU (multiplex network body ECU) via CAN communication to detect a stuck on malfunction of the IGP signal.


HINT:

If DTC P253012 is stored, the ignition switch will turn off (READY off).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P253012 IG2 Signal Circuit Short to Auxiliary Battery The IGP signal of the hybrid vehicle control ECU and the IG control status signal sent from the certification ECU (smart key ECU assembly)*1 or main body ECU (multiplex network body ECU)*2 do not match.
(1 trip detection logic)
·

Auxiliary battery

·

Certification ECU (smart key ECU assembly)*1

·

Ignition or starter switch assembly*2

·

Hybrid vehicle control ECU

·

ECM

·

IGP relay

·

Wire harness or connector


Does not come on Master Warning: Comes on

*1: w/ Smart Key System

*2: w/o Smart Key System

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 15 seconds or more.

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A460751E02
0.563,4.802 1.479,5 0.917,0.198 10 false Auxiliary Battery 0.417,4.125 1.333,4.323 0.917,0.198 10 false BATT-MAIN 0.542,2.417 1.302,2.604 0.76,0.188 10 false IGP-MAIN 1.646,3.292 3.833,3.49 2.188,0.198 10 false No.1 Engine Room Relay Block 6.385,5.844 6.802,6.063 0.417,0.219 10 false ECM 5.219,3.521 7.083,3.823 1.865,0.302 10 false Hybrid Vehicle Control ECU 5.615,0.99 7.115,1.375 1.5,0.385 10 false Certification ECU (Smart Key ECU Assembly)*1 1.969,0.958 3.208,1.333 1.24,0.375 10 false Ignition or Starter Switch Assembly*2 4.938,0.292 5.167,0.49 0.229,0.198 10 false *1 3.448,0.292 3.688,0.458 0.24,0.167 10 false *2 1.458,5.604 4.292,5.813 2.833,0.208 10 false *1: w/ Smart Key System 1.979,0.792 2.323,0.979 0.344,0.188 10 false H54 0.406,1.302 1.51,1.521 1.104,0.219 10 false INP STD NO.1-3 0.927,0.594 1.844,0.792 0.917,0.198 10 false AM1 2.552,2.99 2.885,3.167 0.333,0.177 10 false IGP 4.375,3.063 4.708,3.24 0.333,0.177 10 false INJ 6.396,5.688 6.729,5.865 0.333,0.177 10 false A53 4.667,2.417 5.76,2.594 1.094,0.177 10 false ECU-IGP NO.1 6.313,4.75 6.646,4.927 0.333,0.177 10 false IGP 6.302,5.25 6.635,5.427 0.333,0.177 10 false E1 6.031,4.875 6.365,5.052 0.333,0.177 10 false 10 6.094,5.344 6.427,5.521 0.333,0.177 10 false 6 5.229,3.354 5.563,3.531 0.333,0.177 10 false H44 6.323,2.25 6.656,2.427 0.333,0.177 10 false IGP 6.333,2.896 6.667,3.073 0.333,0.177 10 false E1 6.052,3.031 6.385,3.208 0.333,0.177 10 false 15 6.26,0.427 6.646,0.604 0.385,0.177 10 false IGPD 5.99,0.542 6.323,0.719 0.333,0.177 10 false 24 5.625,0.813 5.958,0.99 0.333,0.177 10 false H45 6.042,2.375 6.375,2.552 0.333,0.177 10 false 26 1.479,5.958 4.552,6.188 3.073,0.229 10 false *2: w/o Smart Key System 2.813,0.542 3.198,0.719 0.385,0.177 10 false IG1 2.104,0.542 2.49,0.719 0.385,0.177 10 false AM1 3.115,0.531 3.354,0.698 0.24,0.167 10 false 8 1.885,0.531 2.125,0.698 0.24,0.167 10 false 7 1.802,2.26 2.135,2.438 0.333,0.177 10 false 2 2.177,2.365 2.51,2.542 0.333,0.177 10 false 3 2.99,2.375 3.323,2.552 0.333,0.177 10 false 5 2.99,2.792 3.323,2.969 0.333,0.177 10 false 1 2.177,2.792 2.51,2.969 0.333,0.177 10 false 2 1.813,2.677 2.146,2.854 0.333,0.177 10 false 2 3.375,2.26 3.708,2.438 0.333,0.177 10 false 2 3.385,2.688 3.719,2.865 0.333,0.177 10 false 2 1.479,0.292 1.719,0.458 0.24,0.167 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

w/ Smart Key System:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK AUXILIARY BATTERY VOLTAGE

Pre-procedure1

a.

Turn the ignition switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.


Procedure1

b.

Measure the auxiliary battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal 20°C (68°F), Ignition switch off 12.0 V or higher



Post-procedure1

c.

None.

Result:
Proceed to
OK
NG




OK

3.CLEAR DTC

NG

2.CHARGE OR REPLACE AUXILIARY BATTERY
2.CHARGE OR REPLACE AUXILIARY BATTERY
a.

Charge or replace the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 15 seconds or more.


b.

Turn the ignition switch off and wait for 2 minutes or more.


Procedure1

c.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P253012 is output A
P253012 is not output B



Post-procedure1

d.

Turn the ignition switch off.



A

5.CHECK VEHICLE CONDITION

B

5.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
w/ Smart Key System A
w/o Smart Key System B



A

6.CHECK DTC OUTPUT (HYBRID CONTROL)

B

11.CHECK DTC OUTPUT (HYBRID CONTROL)
6.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
U012987, U014087, U015187, U016487, U110787 or U117087 is also output A
U012987, U014087, U015187, U016487, U110787 or U117087 is not output B



Post-procedure1

c.

Turn the ignition switch off.



A

7.CHECK HYBRID VEHICLE CONTROL ECU

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK HYBRID VEHICLE CONTROL ECU

Pre-procedure1

a.
A365589C27
1.583,0.125 2.031,0.406 0.448,0.281 1,1.271 0.667,1.854 true 2.688,1.26 3,1.833 true 1.698,0.208 2.01,0.406 0.313,0.198 10 false H44 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 3.01,1.875 3.344,2.115 0.333,0.24 10 false IGP 0.531,1.875 0.865,2.115 0.333,0.24 10 false E1
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the H44 hybrid vehicle control ECU connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Condition:
Tester Connection Condition Specified Condition
H44-26 (IGP) - H44-15 (E1) Ignition switch off 9 V or higher



Post-procedure1

c.

Reconnect the H44 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

8.CHECK ECM

NG

8.CHECK ECM

Pre-procedure1

a.
A365589C28
1.583,0.125 2.031,0.406 0.448,0.281 1,1.271 0.667,1.854 true 2.688,1.26 3,1.833 true 1.698,0.208 2.01,0.406 0.313,0.198 10 false H44 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 3.01,1.875 3.344,2.115 0.333,0.24 10 false IGP 0.531,1.875 0.865,2.115 0.333,0.24 10 false E1
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the H44 hybrid vehicle control ECU connector.


b.

Disconnect the A53 ECM connectors.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Condition:
Tester Connection Condition Specified Condition
H44-26 (IGP) - H44-15 (E1) Ignition switch off 9 V or higher



Post-procedure1

d.

Reconnect the A53 ECM connectors.


e.

Reconnect the H44 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

9.INSPECT IGP RELAY

NG

9.INSPECT IGP RELAY

OK

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK)

NG

REPLACE IGP RELAY

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK)

Pre-procedure1

a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Remove the IGP relay from the No. 1 engine room relay block.


Procedure1

c.
A365589C29
1.583,0.125 2.031,0.406 0.448,0.281 2.688,1.26 3,1.833 true 1.698,0.208 2.01,0.406 0.313,0.198 10 false H44 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 3.01,1.875 3.344,2.115 0.333,0.24 10 false IGP
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H44-26 (IGP) - Body ground Ignition switch off 1 V or less



Post-procedure1

d.

Install the IGP relay.


e.

Reconnect the H44 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block and No. 1 junction block assembly.


ii.

When the ignition switch is ON (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block and No. 1 junction block assembly.




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
U012987, U014087, U015187, U016487 or U117087 is also output A
U012987, U014087, U015187, U016487 or U117087 is not output B



Post-procedure1

c.

Turn the ignition switch off.



A

7.CHECK HYBRID VEHICLE CONTROL ECU

B

12.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
12.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

OK

13.INSPECT IGP RELAY

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

13.INSPECT IGP RELAY

OK

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - NO. 1 ENGINE ROOM RELAY BLOCK)

NG

REPLACE IGP RELAY

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - NO. 1 ENGINE ROOM RELAY BLOCK)
A459393C01
0.229,1.135 0.542,1.333 0.313,0.198 10 false *1 1.01,0.135 1.323,0.333 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGP Relay


Pre-procedure1

a.

Disconnect the H54 ignition or starter switch assembly connector.


b.

Remove the IGP relay from the No. 1 engine room relay block.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (IGP relay holder) - Body ground Ignition switch off 1 V or less



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the ignition or starter switch assembly and the No. 1 engine room relay block and No. 1 junction block assembly.


ii.

When the ignition switch is ON (READY), jiggle the connectors and wire harnesses between the ignition or starter switch assembly and the No. 1 engine room relay block and No. 1 junction block assembly.




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR