Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P274A1C  Transmission Fluid Temperature Sensor "C" Voltage Out of Range  P274A1F  Transmission Fluid Temperature Sensor "C" Circuit Intermittent  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the transmission fluid temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Transmission fluid temperature sensor malfunction
·

Transmission fluid temperature sensor internal malfunction

·

Open or short in transmission fluid temperature sensor


Wire harness between the transmission fluid temperature sensor and hybrid vehicle control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness



DESCRIPTION

Refer to the description for DTC P274A11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P274A11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P274A1C Transmission Fluid Temperature Sensor "C" Voltage Out of Range After a long soak, the value of the transmission fluid temperature sensor is different from the value of the other temperature sensors.
(2 trip detection logic)
·

Wire harness or connector

·

Transmission fluid temperature sensor (Hybrid vehicle transaxle assembly)


Comes on Master Warning: Comes on
P274A1F Transmission Fluid Temperature Sensor "C" Circuit Intermittent Sudden change in transmission fluid temperature sensor output or hunting:
Unusual sudden change in transmission fluid temperature sensor output occurs and offset condition continues for a certain period of time, or unusual change in transmission fluid temperature sensor output occurs repeatedly.
(1 trip detection logic)
·

Wire harness or connector

·

Transmission fluid temperature sensor (Hybrid vehicle transaxle assembly)


Comes on Master Warning: Comes on

Related Data List
DTC No. Data List
P274A1C
·

Generator Temperature

·

Motor Temperature

·

Transaxle Oil Temperature


P274A1F Transaxle Oil Temperature

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


DTC P274A1C
1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off.

3.

Leave the vehicle as is for 5 hours or more and then check the values of the Data List items "Generator Temperature", "Motor Temperature" and "Transaxle Oil Temperature".

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




DTC P274A1F
1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

With ignition switch to ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P274A11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P274A11

PROCEDURE

1.CHECK DTC OUTPUT (ENGINE)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B


Relevant DTC
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid


Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B


Relevant DTC
P274A11 Transmission Fluid Temperature Sensor "C" Circuit Short to Ground
P274A15 Transmission Fluid Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open


Post-procedure1

c.

Turn the ignition switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION FLUID TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION FLUID TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

Pre-procedure1

a.

Disconnect the A68 hybrid vehicle control ECU connector.


Procedure1

b.
A460761C07
1.5,0.146 1.938,0.365 0.438,0.219 1.594,1.573 1.417,1.844 true 1.76,1.552 1.885,1.823 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 1.583,0.177 1.958,0.385 0.375,0.208 10 false A68 1.958,1.865 2.458,2.052 0.5,0.188 10 false ETTA 1.115,1.865 1.615,2.052 0.5,0.188 10 false TTA
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-41 (TTA) - A68-42 (ETTA) Ignition switch off 1.393 to 75.8 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

c.

Reconnect the A68 hybrid vehicle control ECU connector.



OK

5.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)

NG

9.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)
5.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P274A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY)

Pre-procedure1

a.

Disconnect the DA2 No. 1 engine room relay block and No. 1 junction block assembly connector.


b.

Disconnect the A68 hybrid vehicle control ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

HINT:

When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
DA2-19 (TTA) - A68-41 (TTA) Ignition switch off Below 1 Ω
DA2-18 (ETTA) - A68-42 (ETTA) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
DA2-19 (TTA) or A68-41 (TTA) - Body ground and other terminals Ignition switch off 10 kΩ or higher
DA2-18 (ETTA) or A68-42 (ETTA) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

Reconnect the A68 hybrid vehicle control ECU connector.


e.

Reconnect the DA2 No. 1 engine room relay block and No. 1 junction block assembly connector.



OK

7.CHECK CONNECTOR CONNECTION CONDITION (TRANSMISSION FLUID TEMPERATURE SENSOR CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CONNECTOR CONNECTION CONDITION (TRANSMISSION FLUID TEMPERATURE SENSOR CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P274A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

8.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY - MOTOR TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY - MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.

Disconnect the D60 transmission fluid temperature sensor connector.


b.

Disconnect the DA2 No. 1 engine room relay block and No. 1 junction block assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

HINT:

When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
DA2-19 (TTA) - D60-3 (TTA) Ignition switch off Below 1 Ω
DA2-18 (ETTA) - D60-13 (ETTA) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
DA2-19 (TTA) or D60-3 (TTA) - Body ground and other terminals Ignition switch off 10 kΩ or higher
DA2-18 (ETTA) or D60-13 (ETTA) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

Reconnect the DA2 No. 1 engine room relay block and No. 1 junction block assembly connector.


e.

Reconnect the D60 transmission fluid temperature sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)

Pre-procedure1

a.

Disconnect the DA2 No. 1 engine room relay block and No. 1 junction block assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DA2-19 (TTA) - DA2-18 (ETTA) Ignition switch off 1.393 to 75.8 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

c.

Reconnect the DA2 No. 1 engine room relay block and No. 1 junction block assembly connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY)

NG

10.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)
10.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - TRANSMISSION FLUID TEMPERATURE SENSOR)

NG