Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P310711  Lost Communication with Airbag System Control Module Circuit Short to Ground  


DESCRIPTION

The hybrid vehicle control ECU detects a problem in the collision signal line from the airbag sensor assembly and alerts the driver.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P310711 Lost Communication with Airbag System Control Module Circuit Short to Ground Short to ground in the communication circuit:
Communication from the airbag sensor assembly stopped and Circuit Low has been detected for a certain period.
(1 trip detection logic)
·

Wire harness or connector

·

Airbag sensor assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning: Comes on

Related Data List
DTC No. Data List
P310711 Airbag Status (Collision)

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

With ignition switch to ON and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A409148E19
1.917,0.979 2.531,1.177 0.615,0.198 10 false GSW2 2.146,1.302 2.76,1.5 0.615,0.198 10 false E1 2.406,1.302 3.021,1.5 0.615,0.198 10 false 33 2.406,0.979 3.021,1.177 0.615,0.198 10 false 24 1.042,2.094 1.656,2.292 0.615,0.198 10 false H14 1.042,2.229 2.896,2.542 1.854,0.313 10 false Airbag Sensor Assembly 4.625,0.969 4.865,1.167 0.24,0.198 10 false 44 4.906,1 5.521,1.198 0.615,0.198 10 false ABFS 4.521,2.042 5.135,2.24 0.615,0.198 10 false H44 5.781,1.542 6.396,1.74 0.615,0.198 10 false E1 4.521,2.198 6.417,2.51 1.896,0.313 10 false Hybrid Vehicle Control ECU 6.083,1.427 6.698,1.625 0.615,0.198 10 false 15 5.552,0.479 6.167,0.677 0.615,0.198 10 false +B

PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

Pre-procedure1

a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below.


b.

Turn the ignition switch to ON (READY).


Procedure1

c.

Measure the waveform.

A459747C01
4.635,0.188 5.073,0.448 0.438,0.26 6.135,2.448 5.552,1.354 true 4.74,2.448 5.313,1.594 true 4.615,3.531 5.073,3.729 0.458,0.198 10 false GND 4.75,0.26 5.208,0.458 0.458,0.198 10 false H44 6.125,2.479 6.583,2.677 0.458,0.198 10 false E1 4.51,2.479 4.969,2.677 0.458,0.198 10 false ABFS 0.5,0.135 0.958,0.333 0.458,0.198 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Item Contents
Terminal H44-44 (ABFS) - H44-15 (E1)
Equipment Setting 5 V/DIV., 150 ms./DIV.
Condition Ignition switch ON (READY)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B



Post-procedure1

d.

Turn the ignition switch off.



A

3.CLEAR DTC

B

6.CHECK AIRBAG SENSOR ASSEMBLY
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P310711 is not output A
P310711 is output B



Post-procedure1

c.

Turn the ignition switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK AIRBAG SENSOR ASSEMBLY

Pre-procedure1

a.

Disconnect the H14 airbag sensor assembly connector.


Procedure1

b.
A460067C01
1.333,0.135 1.76,0.385 0.427,0.25 2.042,1.771 1.5,1.073 true 1.104,1.76 1.5,1.188 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.427,0.198 1.74,0.354 0.313,0.156 10 false H14 2.083,1.792 2.604,1.979 0.521,0.188 10 false GSW2 0.969,1.792 1.281,1.948 0.313,0.156 10 false E1
*a Component without harness connected
(Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H14-24 (GSW2) - H14-33 (E1) Ignition switch off 10 kΩ or higher



Post-procedure1

c.

Reconnect the H14 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Disconnect the H14 airbag sensor assembly connector.


Procedure1

c.
A409134C10
0.438,3.25 0.875,3.531 0.438,0.281 1.542,0.146 1.979,0.427 0.438,0.281 1.51,1.938 1.24,1.531 true 2.24,4.177 1.823,3.5 true 0.156,0.177 0.469,0.333 0.313,0.156 10 false *a 0.156,2.208 0.469,2.365 0.313,0.156 10 false *b 2.292,4.219 2.906,4.417 0.615,0.198 10 false GSW2 1.531,1.948 2.146,2.146 0.615,0.198 10 false ABFS 0.552,3.333 1.167,3.531 0.615,0.198 10 false H14 1.656,0.219 2.271,0.417 0.615,0.198 10 false H44
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H44-44 (ABFS) or H14-24 (GSW2) - Body ground and other terminals Ignition switch off 10 kΩ or higher



Post-procedure1

d.

Reconnect the H14 airbag sensor assembly connector.


e.

Reconnect the H44 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR