Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Pattern Select Switch EV Mode Circuit  


DESCRIPTION

The EV mode signal will be sent to the hybrid vehicle control ECU when the EV mode switch (combination switch assembly) is operated. If the specified conditions are met, the system enters EV mode and the vehicle will be driven using EV mode. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter assembly to illuminate the EV mode indicator.

WIRING DIAGRAM

C280820E48
1.552,1.208 3.5,1.521 1.948,0.313 10 false Combination Meter Assembly 1.302,2.906 4.365,3.135 3.063,0.229 10 false EV Mode Switch (Combination Switch Assembly) 4.719,2.865 6.5,3.354 1.781,0.49 10 false Hybrid Vehicle Control ECU 5.104,2.063 5.688,2.323 0.583,0.26 10 false EVSW 4.802,2.063 5.083,2.344 0.281,0.281 10 false 33 4.719,2.698 5,2.979 0.281,0.281 10 false H44 1.302,2.719 1.656,2.906 0.354,0.188 10 false H18 5.792,1.75 6.073,2.031 0.281,0.281 10 false +B 1.563,2.063 1.844,2.344 0.281,0.281 10 false 5 1.76,2.073 2.25,2.271 0.49,0.198 10 false E 2.99,2.063 3.188,2.302 0.198,0.24 10 false S 0.583,3.385 2.531,3.698 1.948,0.313 10 false : CAN Communication Line 3.198,2.073 3.563,2.344 0.365,0.271 10 false 6 2.167,1.865 2.906,2.042 0.74,0.177 10 false EV MODE

CAUTION / NOTICE / HINT

Depending on the condition of the hybrid control system and the driving conditions, the drive mode may not be able to be changed to EV drive mode and a warning message will be displayed on the multi-information display.

HINT:

Under the following conditions, the drive mode will not be able to be changed to EV drive mode:

·

The hybrid control system is extremely hot.

·

The hybrid control system is extremely cold.

·

The engine is warming up.

·

The SOC (State of Charge) of the HV battery is low.

·

The vehicle is being driven at a speed higher than the specified value.

·

The accelerator pedal is being fully depressed or the vehicle is climbing a slope.

·

The defroster is on.

·

DTCs are stored.



PROCEDURE

1.ASK ABOUT VEHICLE CONDITION
a.

Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV mode.

Result:
Result Proceed to
No buzzer sounded and no message was displayed on multi-information display A
A buzzer sounded and a message was displayed on multi-information display B


HINT:

If a buzzer sounds and a message is displayed on the multi-information display, one or more of the EV mode entry conditions have not been met.




A

2.READ VALUE USING GTS (CAN BUS CHECK)

B

END

2.READ VALUE USING GTS (CAN BUS CHECK)
a.

Enter the following menus: System Select / CAN Bus Check.

CAN Bus Check
50007
Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



b.

Turn the ignition switch off.



A

3.CHECK DTC OUTPUT (HEALTH CHECK)

B

3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Enter the following menus: System Select / Health Check.


b.

Check for DTCs.

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



c.

Turn the ignition switch off.



A

4.READ VALUE USING GTS (EV MODE, EV MODE SWITCH)

B

GO TO DTC CHART

4.READ VALUE USING GTS (EV MODE, EV MODE SWITCH)
a.

Read the values displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
EV Mode EV mode transition availability ON or OFF In EV drive mode: ON
EV Mode Switch EV mode switch condition ON or OFF EV mode switch being pushed and held: ON
EV mode switch not operated: OFF
Powertrain > Hybrid Control > Data List
Tester Display
EV Mode
EV Mode Switch
50003 397 79,80
Result:
Result Proceed to
The display changes according to the EV mode switch operation A
The display does not change according to the EV mode switch operation B



b.

Turn the ignition switch off.



A

B

5.INSPECT EV MODE SWITCH (COMBINATION SWITCH ASSEMBLY)
5.INSPECT EV MODE SWITCH (COMBINATION SWITCH ASSEMBLY)

OK

6.CHECK HARNESS AND CONNECTOR (EV MODE SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (EV MODE SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the H18 EV mode switch (combination switch assembly) connector.


b.
A368640C12
0.417,1 0.844,1.302 0.427,0.302 1.104,1.823 1.375,1.5 true 0.188,0.198 0.5,0.354 0.313,0.156 10 false *a 0.521,1.083 0.833,1.24 0.313,0.156 10 false H18 1.021,1.865 1.188,2.042 0.167,0.177 10 false E
*a Front view of wire harness connector
(to EV Mode Switch (Combination Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-5 (E) - Body ground Always Below 1 Ω



c.

Reconnect the H18 EV mode switch (combination switch assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV MODE SWITCH (COMBINATION SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV MODE SWITCH (COMBINATION SWITCH ASSEMBLY))
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Disconnect the H18 EV mode switch (combination switch assembly) connector.


c.
A368646C34
1.625,0.219 2.115,0.51 0.49,0.292 1.49,2.542 1.979,2.833 0.49,0.292 1.938,2.115 1.646,1.552 true 1.896,4.208 1.656,3.76 true 0.302,0.177 0.615,0.333 0.313,0.156 10 false *a 0.333,2.76 0.646,2.917 0.313,0.156 10 false *b 1.635,2.625 1.948,2.781 0.313,0.156 10 false H18 1.771,0.302 2.083,0.458 0.313,0.156 10 false H44 1.906,2.177 2.458,2.406 0.552,0.229 10 false EVSW 1.896,4.281 2.177,4.479 0.281,0.198 10 false S
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to EV Mode Switch (Combination Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H44-33 (EVSW) - H18-6 (S) Always Below 1 Ω
H44-33 (EVSW) or H18-6 (S) - Body ground Always 10 kΩ or higher



d.

Reconnect the H18 EV mode switch (combination switch assembly) connector.


e.

Reconnect the H44 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR