Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _087984 INTERIOR PANELS / TRIM _0420192 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


PROCEDURE

Hide 86101J 1.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

Hide 82171 2.INSTALL NO. 1 ROOF WIRE

a.
B574262C01
0,0 0,0 false
V113147

Install in this Direction


Turn the visor connectors approximately 90° clockwise to connect the visor connector as shown in the illustration.

HINT:

Use the same procedures for the opposite side.



b.

Line up the No. 1 roof wire positioning tape and the roof headlining markings.

B575455C01
4.219,2.781 4.479,2.479 4.479,2.479 4.198,2.219 true 3.198,2.188 3.552,2.458 true 1.125,1.729 0.656,1.594 0.656,1.594 1.021,1.094 true 0.656,1.594 1.135,1.167 true 0.469,3.281 0.427,2.688 0.427,2.688 1.313,2.552 true 5.219,3.292 5.563,3.552 true 4.51,2.375 4.74,2.563 0.229,0.188 10 true *a 0.385,1.51 0.615,1.698 0.229,0.188 10 true *a 0.219,2.604 0.448,2.792 0.229,0.188 10 true *a 3.021,2.083 3.25,2.271 0.229,0.188 10 true *a 5.615,3.479 5.844,3.667 0.229,0.188 10 true *b
*a Positioning Tape *b Marking



c.

Install the No. 1 roof wire with 24 new pieces of adhesive tape.

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.



HINT:

Adjust the slack of the No. 1 roof wire as shown in the adjustment area of illustration.


B575456C01
0.375,2.323 0.563,2.406 true 3.24,1.823 3.427,1.99 true 4.063,2.948 4.385,3.135 true 3.042,1.708 3.24,1.906 0.198,0.198 10 true *a 4.417,3.042 4.615,3.24 0.198,0.198 10 true *a 0.177,2.24 0.375,2.438 0.198,0.198 10 true *a
*a Adjustment Area - -



Hide 63343B 3.INSTALL REAR ROOF SILENCER PAD

a.

Align the markings on the roof headlining with the 2 rear roof silencer pads and install them using hot melt glue.

B576281C01
5.542,2.302 5.125,2.219 true 4.896,2.104 5.115,2.302 0.219,0.198 10 true *a
*a Marking - -



Hide 63341 4.INSTALL NO. 1 ROOF SILENCER PAD

a.

Align the markings on the roof headlining with the 3 No. 1 roof silencer pads and install them using hot melt glue.

B576409C01
3.969,2.802 3.719,2.729 true 3.49,2.635 3.708,2.792 0.219,0.156 10 true *a
*a Marking - -



Hide 63342 5.INSTALL NO. 2 ROOF SILENCER PAD

a.

Align the markings on the roof headlining with the No. 2 roof silencer pad and install them using hot melt glue.

B576410C01
3.833,2.969 3.583,2.896 true 3.865,2.938 4.083,3.094 0.219,0.156 10 true *a
*a Marking - -



Hide 63345 6.INSTALL NO. 5 ROOF SILENCER PAD

a.

Align the markings on the roof headlining with the 2 No. 5 roof silencer pads and install them using hot melt glue.

B576411C01
2.625,2.542 3.083,2.365 true 3.104,2.26 3.323,2.458 0.219,0.198 10 true *a
*a Marking - -