This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B150013 | Fuel Sender Circuit Open | Diagnosis Condition:
·
The ignition switch is ON ·
IG power source voltage is 9.5 V or more Malfunction Status: ·
Voltage signal from fuel sender gauge assembly is 0.2 V or less ·
Voltage signal from fuel sender gauge assembly is 4.7 V or more Malfunction Time: 10 seconds or more |
·
Harness or connector ·
Fuel sender gauge assembly ·
Fuel suction tube with pump and gauge assembly ·
Combination meter assembly |
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fuel Input | Fuel input | Min.: 0.00 L, Max.: 655.35 L or Unset | Fuel sender input value | - |
| Tester Display |
|---|
| Fuel Input |
| Result | Proceed to |
|---|---|
| Fuel level data can be displayed on the GTS. | A |
| Fuel level data cannot be displayed on the GTS | B |
A
B
Pre-procedure1
Disconnect the O22 fuel suction tube with pump and gauge assembly connector.
Disconnect the H6 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O22-1 (FV) - H6-14 (FV) | Always | Below 1 Ω |
| O22-3 (FS) - H6-31 (FR) | Always | Below 1 Ω |
| O22-2 (FE) - H6-24 (FE&B) | Always | Below 1 Ω |
| O22-1 (FV) or H6-14 (FV) - Body ground | Always | 10 kΩ or higher |
| O22-3 (FS) or H6-31 (FR) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for M15A-FKS | A |
| for M15A-FXE | B |
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O22-1 (FV) - A-3 | Always | Below 1 Ω |
| O22-2 (FE) - A-2 | Always | Below 1 Ω |
| O22-3 (FS) - A-1 | Always | Below 1 Ω |
| O22-1 (FV) - O22-3 (FS) or A-3 - A-1 | Always | 10 kΩ or higher |
| O22-1 (FV) - O22-2 (FE) or A-3 - A-2 | Always | 10 kΩ or higher |
| O22-2 (FE) - O22-3 (FS) or A-2 - A-1 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for M15A-FKS:
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for M15A-FXE:
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL