This DTC is stored when the combination meter assembly detects a short in a turn signal light circuit.
If there is a short in a turn signal light circuit, all of the turn signal lights in that circuit will not blink.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B150819 | Turn Signal/Hazard Flasher Circuit Current Above Threshold | Diagnosis Condition:
Auxiliary battery voltage is 10 V or more Malfunction Status: Short in turn signal light circuit |
·
Headlight assembly -
Front turn signal light socket*1 -
Front turn signal light bulb*1 -
Headlight unit LH*2 -
Headlight unit RH*2 -
Wire Harness LH*2 -
Wire Harness RH*2 ·
Outer rear view mirror assembly -
Side turn signal light assembly LH -
Side turn signal light assembly RH ·
Rear combination light assembly -
Rear turn signal light socket*1 -
Rear turn signal light bulb*1 -
Rear turn signal light LED*2 ·
Harness or connector ·
Combination meter assembly |
*1: for Halogen Headlight
*2: for LED Headlight
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the turn signal light bulbs before performing the following procedure.
Check the problem symptoms.
| Result | Proceed to |
|---|---|
| All LH side turn signal lights do not blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for Halogen Headlight | A |
| for LED Headlight | B |
A
B
Pre-procedure1
Disconnect the A16 headlight assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.
If the LH side turn signal lights other than the front turn signal light blink, the headlight assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the front turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/o Mirror Heater | A |
| w/ Mirror Heater | B |
A
B
Pre-procedure1
Connect the A16 headlight assembly LH connector.
Disconnect the L10 outer rear view mirror assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If the LH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Remove the side turn signal light assembly LH from outer rear view mirror assembly LH.
Connect the L10 outer rear view mirror assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Connect the L10 outer rear view mirror assembly LH connector.
Disconnect the T1 rear combination light assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.
If the LH side turn signal lights other than the rear turn signal light blink, the rear combination light assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the rear turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for Halogen Headlight)>DISASSEMBLY
B
Pre-procedure1
Disconnect the A16 headlight assembly LH connector.
Disconnect the L10 outer rear view mirror assembly LH connector.
Disconnect the H7 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A16-1 (B) - Body ground | Always | 10 kΩ or higher |
| L10-4 (B) - Body ground | Always | 10 kΩ or higher |
| T1-1 (B) - Body ground | Always | 10 kΩ or higher |
| H7-1 (LL) - Body ground | Always | 10 kΩ or higher |
| H7-5 (TRNL) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Connect the A16 headlight assembly LH connector.
Disconnect the L8 outer rear view mirror assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If the LH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Remove the side turn signal light assembly LH from outer rear view mirror assembly LH.
Connect the L8 outer rear view mirror assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Connect the L8 outer rear view mirror assembly LH connector.
Disconnect the T1 rear combination light assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.
If the LH side turn signal lights other than the rear turn signal light blink, the rear combination light assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the rear turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for Halogen Headlight)>DISASSEMBLY
B
Pre-procedure1
Disconnect the A16 headlight assembly LH connector.
Disconnect the L8 outer rear view mirror assembly LH connector.
Disconnect the H7 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A16-1 (B) - Body ground | Always | 10 kΩ or higher |
| L8-16 (B) - Body ground | Always | 10 kΩ or higher |
| T1-1 (B) - Body ground | Always | 10 kΩ or higher |
| H7-1 (LL) - Body ground | Always | 10 kΩ or higher |
| H7-5 (TRNL) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the A4 headlight assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.
If the LH side turn signal lights other than the front turn signal light blink, the headlight assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the front turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Remove the headlight unit LH from headlight assembly LH.
Connect the A4 headlight assembly LH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.
If all LH side turn signal lights do not blink, the wire harness LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the front turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/o Mirror Heater | A |
| w/ Mirror Heater | B |
A
B
Pre-procedure1
Connect the A4 headlight assembly LH connector.
Disconnect the L10 outer rear view mirror assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If the LH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Remove the side turn signal light assembly LH from outer rear view mirror assembly LH.
Connect the L10 outer rear view mirror assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Connect the L10 outer rear view mirror assembly LH connector.
Disconnect the T3 rear combination light assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.
If the LH side turn signal lights other than the rear turn signal light blink, the rear combination light assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the rear turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
B
Pre-procedure1
Disconnect the A4 headlight assembly LH connector.
Disconnect the L10 outer rear view mirror assembly LH connector.
Disconnect the H7 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-6 (B) - Body ground | Always | 10 kΩ or higher |
| L10-4 (B) - Body ground | Always | 10 kΩ or higher |
| T3-2 (B) - Body ground | Always | 10 kΩ or higher |
| H7-1 (LL) - Body ground | Always | 10 kΩ or higher |
| H7-5 (TRNL) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Connect the A4 headlight assembly LH connector.
Disconnect the L8 outer rear view mirror assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If the LH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Remove the side turn signal light assembly LH from outer rear view mirror assembly LH.
Connect the L8 outer rear view mirror assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.
If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the side turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Connect the L8 outer rear view mirror assembly LH connector.
Disconnect the T3 rear combination light assembly LH connector.
Procedure1
Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.
If the LH side turn signal lights other than the rear turn signal light blink, the rear combination light assembly LH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the rear turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
B
Pre-procedure1
Disconnect the A4 headlight assembly LH connector.
Disconnect the L8 outer rear view mirror assembly LH connector.
Disconnect the H7 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-6 (B) - Body ground | Always | 10 kΩ or higher |
| L8-16 (B) - Body ground | Always | 10 kΩ or higher |
| T3-2 (B) - Body ground | Always | 10 kΩ or higher |
| H7-1 (LL) - Body ground | Always | 10 kΩ or higher |
| H7-5 (TRNL) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for Halogen Headlight | A |
| for LED Headlight | B |
A
B
Pre-procedure1
Disconnect the A17 headlight assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the front turn signal light blink.
If the RH side turn signal lights other than the front turn signal light blink, the headlight assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the front turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/o Mirror Heater | A |
| w/ Mirror Heater | B |
A
B
Pre-procedure1
Connect the A17 headlight assembly RH connector.
Disconnect the K10 outer rear view mirror assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If the RH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Remove the side turn signal light assembly RH from outer rear view mirror assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Connect the K10 outer rear view mirror assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Connect the K10 outer rear view mirror assembly RH connector.
Disconnect the S1 rear combination light assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.
If the RH side turn signal lights other than the rear turn signal light blink, the rear combination light cord RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the rear turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for Halogen Headlight)>DISASSEMBLY
B
Pre-procedure1
Disconnect the A17 headlight assembly RH connector.
Disconnect the K10 outer rear view mirror assembly RH connector.
Disconnect the H7 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A17-1 (B) - Body ground | Always | 10 kΩ or higher |
| K10-4 (B) - Body ground | Always | 10 kΩ or higher |
| S1-1 (B) - Body ground | Always | 10 kΩ or higher |
| H7-2 (LR) - Body ground | Always | 10 kΩ or higher |
| H7-6 (TRNR) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Connect the A17 headlight assembly RH connector.
Disconnect the K8 outer rear view mirror assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If the RH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Remove the side turn signal light assembly RH from outer rear view mirror assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Connect the K8 outer rear view mirror assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Connect the K8 outer rear view mirror assembly RH connector.
Disconnect the S1 rear combination light assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.
If the RH side turn signal lights other than the rear turn signal light blink, the rear combination light cord RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the rear turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for Halogen Headlight)>DISASSEMBLY
B
Pre-procedure1
Disconnect the A17 headlight assembly RH connector.
Disconnect the K8 outer rear view mirror assembly RH connector.
Disconnect the H7 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A17-1 (B) - Body ground | Always | 10 kΩ or higher |
| K8-16 (B) - Body ground | Always | 10 kΩ or higher |
| S1-1 (B) - Body ground | Always | 10 kΩ or higher |
| H7-2 (LR) - Body ground | Always | 10 kΩ or higher |
| H7-6 (TRNR) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the A5 headlight assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the front turn signal light blink.
If the RH side turn signal lights other than the front turn signal light blink, the headlight assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the front turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Remove the headlight unit RH from headlight assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
Connect the A5 headlight assembly RH connector.
Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.
If all LH side turn signal lights do not blink, the wire harness RH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights other than the front turn signal light blink | A |
| All LH side turn signal lights do not blink | B |
A
B
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/o Mirror Heater | A |
| w/ Mirror Heater | B |
A
B
Pre-procedure1
Connect the A5 headlight assembly RH connector.
Disconnect the K10 outer rear view mirror assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If the RH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Remove the side turn signal light assembly RH from outer rear view mirror assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Connect the K10 outer rear view mirror assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Connect the K10 outer rear view mirror assembly RH connector.
Disconnect the S3 rear combination light assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.
If the RH side turn signal lights other than the rear turn signal light blink, the rear combination light cord RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the rear turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
B
Pre-procedure1
Disconnect the A5 headlight assembly RH connector.
Disconnect the K10 outer rear view mirror assembly RH connector.
Disconnect the H7 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-6 (B) - Body ground | Always | 10 kΩ or higher |
| K10-4 (B) - Body ground | Always | 10 kΩ or higher |
| S3-2 (B) - Body ground | Always | 10 kΩ or higher |
| H7-2 (LR) - Body ground | Always | 10 kΩ or higher |
| H7-6 (TRNR) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Connect the A5 headlight assembly RH connector.
Disconnect the K8 outer rear view mirror assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If the RH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Remove the side turn signal light assembly RH from outer rear view mirror assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Connect the K8 outer rear view mirror assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.
If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the side turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
B
Pre-procedure1
Connect the K8 outer rear view mirror assembly RH connector.
Disconnect the S3 rear combination light assembly RH connector.
Procedure1
Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.
If the RH side turn signal lights other than the rear turn signal light blink, the rear combination light cord RH is malfunctioning.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| RH side turn signal lights other than the rear turn signal light blink | A |
| All RH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
B
Pre-procedure1
Disconnect the A5 headlight assembly RH connector.
Disconnect the K8 outer rear view mirror assembly RH connector.
Disconnect the H7 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-6 (B) - Body ground | Always | 10 kΩ or higher |
| K8-16 (B) - Body ground | Always | 10 kΩ or higher |
| S3-2 (B) - Body ground | Always | 10 kΩ or higher |
| H7-2 (LR) - Body ground | Always | 10 kΩ or higher |
| H7-6 (TRNR) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG