Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2020.03–2020.07
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0420300 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2311  Power Window Motor Malfunction  


DESCRIPTION

The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies. The power window regulator motor assemblies have motor, regulator and ECU functions.

This DTC is stored when a power window regulator motor assembly is malfunctioning, or the ECU built into the power window regulator motor assembly determines that the fully closed power window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

D-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction
Either condition is met:
1.

Power window regulator motor assembly (for driver door) is malfunctioning

2.

ECU in power window regulator motor assembly (for driver door) determines that fully closed power window position has deviated approx. 20 mm (0.787 in.) or more from normal position


·

Power window regulator motor assembly (for driver door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly (for driver door)

·

Wire harness or connector



P-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction
Either condition is met:
1.

Power window regulator motor assembly (for front passenger door) is malfunctioning

2.

ECU in power window regulator motor assembly (for front passenger door) determines that fully closed power window position has deviated approx. 20 mm (0.787 in.) or more from normal position


·

Power window regulator motor assembly (for front passenger door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly (for front passenger door)

·

Wire harness or connector



RL-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction
Either condition is met:
1.

Power window regulator motor assembly (for rear LH door) is malfunctioning

2.

ECU in power window regulator motor assembly (for rear LH door) determines that fully closed power window position has deviated approx. 20 mm (0.787 in.) or more from normal position


·

Power window regulator motor assembly (for rear LH door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly (for rear LH door)

·

Wire harness or connector



RR-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction
Either condition is met:
1.

Power window regulator motor assembly (for rear RH door) is malfunctioning

2.

ECU in power window regulator motor assembly (for rear RH door) determines that fully closed power window position has deviated approx. 20 mm (0.787 in.) or more from normal position


·

Power window regulator motor assembly (for rear RH door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly (for rear RH door)

·

Wire harness or connector



WIRING DIAGRAM

E437949E04
1,1.896 1.531,2.146 0.531,0.25 10 false GND 1.021,1.104 1.552,1.354 0.531,0.25 10 false B 2.271,1.104 2.802,1.354 0.531,0.25 10 false UP 2.031,1.427 2.563,1.677 0.531,0.25 10 false DOWN 2.094,4.156 2.625,4.406 0.531,0.25 10 false AUTO 0.938,2.573 2.521,2.969 1.583,0.396 10 false Multiplex Network Master Switch Assembly 3.552,2.594 5.531,3.021 1.979,0.427 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.458,1.26 6.302,1.5 0.844,0.24 10 false DOOR F/R 5.365,0.615 6.271,0.833 0.906,0.219 10 false ECU-B NO. 2 3.646,0.156 5.354,0.49 1.708,0.333 10 false from Auxiliary Battery 3.604,5.021 6.208,5.521 2.604,0.5 10 false Power Window Regulator Motor Assembly (for Front Passenger Door) 0.948,5.01 2.5,5.417 1.552,0.406 10 false Power Window Regulator Switch Assembly 0.563,7.49 2.896,7.927 2.333,0.438 10 false Rear Power Window Regulator Switch Assembly (for RH Door) 0.844,8.302 2.625,8.542 1.781,0.24 10 false : LIN Communication Line 3.583,7.521 5.542,8.115 1.958,0.594 10 false Power Window Regulator Motor Assembly (for Rear RH Door) 5.448,6.177 6.229,6.427 0.781,0.25 10 false DOOR R/R 3.667,1.115 4.198,1.365 0.531,0.25 10 false UP 3.688,3.521 4.219,3.771 0.531,0.25 10 false UP 2.25,3.521 2.781,3.771 0.531,0.25 10 false UP 2.271,5.99 2.802,6.24 0.531,0.25 10 false UP 3.667,6.01 4.198,6.26 0.531,0.25 10 false UP 3.656,1.417 4.188,1.667 0.531,0.25 10 false DOWN 3.656,3.833 4.188,4.083 0.531,0.25 10 false DOWN 2.031,3.844 2.563,4.094 0.531,0.25 10 false DOWN 2.031,6.333 2.563,6.583 0.531,0.25 10 false DOWN 3.656,6.333 4.188,6.583 0.531,0.25 10 false DOWN 3.667,4.146 4.198,4.396 0.531,0.25 10 false AUTO 3.667,6.667 4.198,6.917 0.531,0.25 10 false AUTO 2.104,6.667 2.635,6.917 0.531,0.25 10 false AUTO 1.021,4.313 1.552,4.563 0.531,0.25 10 false GND 1,6.823 1.531,7.073 0.531,0.25 10 false GND 4.906,6.833 5.438,7.083 0.531,0.25 10 false GND 4.906,4.313 5.438,4.563 0.531,0.25 10 false GND 4.906,1.896 5.438,2.146 0.531,0.25 10 false GND 5.115,1.104 5.646,1.354 0.531,0.25 10 false B 5.479,3.688 6.26,3.938 0.781,0.25 10 false DOOR F/L 5.104,3.521 5.635,3.771 0.531,0.25 10 false B 5.094,6.021 5.625,6.271 0.531,0.25 10 false B 0.75,1 1.281,1.25 0.531,0.25 10 false 11 2.552,1.01 3.083,1.26 0.531,0.25 10 false 20 0.75,1.792 1.281,2.042 0.531,0.25 10 false 12 2.552,1.323 3.083,1.573 0.531,0.25 10 false 15 3.427,1.021 3.958,1.271 0.531,0.25 10 false 10 3.49,1.333 4.021,1.583 0.531,0.25 10 false 7 5.313,1.01 5.844,1.26 0.531,0.25 10 false 2 5.302,1.792 5.833,2.042 0.531,0.25 10 false 1 3.552,2.427 4.083,2.677 0.531,0.25 10 false K7 0.927,2.417 1.458,2.667 0.531,0.25 10 false K5 0.958,4.854 1.49,5.104 0.531,0.25 10 false L6 0.563,7.323 1.094,7.573 0.531,0.25 10 false M3 3.583,7.333 4.115,7.583 0.531,0.25 10 false M4 3.615,4.844 4.146,5.094 0.531,0.25 10 false L7 3.49,4.052 4.021,4.302 0.531,0.25 10 false 4 2.563,4.042 3.094,4.292 0.531,0.25 10 false 8 0.823,4.156 1.354,4.406 0.531,0.25 10 false 7 0.823,6.719 1.354,6.969 0.531,0.25 10 false 7 5.281,4.177 5.813,4.427 0.531,0.25 10 false 1 5.281,6.719 5.813,6.969 0.531,0.25 10 false 1 3.417,3.427 3.948,3.677 0.531,0.25 10 false 10 3.406,5.906 3.938,6.156 0.531,0.25 10 false 10 3.49,3.74 4.021,3.99 0.531,0.25 10 false 7 3.49,6.24 4.021,6.49 0.531,0.25 10 false 7 3.5,6.573 4.031,6.823 0.531,0.25 10 false 4 2.563,3.729 3.094,3.979 0.531,0.25 10 false 4 2.552,3.417 3.083,3.667 0.531,0.25 10 false 5 5.302,3.438 5.833,3.688 0.531,0.25 10 false 2 5.292,5.917 5.823,6.167 0.531,0.25 10 false 2 2.563,6.573 3.094,6.823 0.531,0.25 10 false 8 2.563,6.24 3.094,6.49 0.531,0.25 10 false 4 2.563,5.906 3.094,6.156 0.531,0.25 10 false 5 6.292,8.292 6.448,8.49 0.156,0.198 10 false A

E437950E04
0.49,1.958 0.979,2.208 0.49,0.25 10 false N3 0.5,2.125 2.813,2.51 2.313,0.385 10 false Rear Power Window Regulator Switch Assembly (for LH Door) 0.76,3.875 2.396,4.323 1.635,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 4.188,1.979 4.5,2.177 0.313,0.198 10 false N4 4.188,2.156 6.146,2.74 1.958,0.583 10 false Power Window Regulator Motor Assembly (for Rear LH Door) 3.99,0.573 4.333,0.781 0.344,0.208 10 false 10 4.063,0.906 4.406,1.115 0.344,0.208 10 false 7 4.052,1.229 4.396,1.438 0.344,0.208 10 false 4 2.406,0.573 2.75,0.781 0.344,0.208 10 false 5 2.406,0.917 2.75,1.125 0.344,0.208 10 false 4 2.417,1.25 2.76,1.458 0.344,0.208 10 false 8 2.115,0.656 2.729,0.875 0.615,0.219 10 false UP 1.885,1 2.5,1.219 0.615,0.219 10 false DOWN 1.927,1.323 2.542,1.542 0.615,0.219 10 false AUTO 0.854,1.479 1.469,1.698 0.615,0.219 10 false GND 6.063,0.813 6.844,1.021 0.781,0.208 10 false DOOR R/L 5.667,0.667 6.281,0.885 0.615,0.219 10 false B 5.417,4.375 7.021,4.625 1.604,0.25 10 false : LIN Communication Line 0.646,1.365 0.99,1.573 0.344,0.208 10 false 7 5.865,0.573 6.479,0.792 0.615,0.219 10 false 2 5.865,1.281 6.479,1.5 0.615,0.219 10 false 1 5.5,1.375 6.115,1.594 0.615,0.219 10 false GND 4.24,0.667 4.854,0.885 0.615,0.219 10 false UP 4.24,1 4.854,1.219 0.615,0.219 10 false DOWN 4.229,1.323 4.844,1.542 0.615,0.219 10 false AUTO 6.802,0.229 6.958,0.427 0.156,0.198 10 false A

CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2311 is stored in each power window regulator motor assembly.

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144
Body Electrical > RL-Door Motor > Trouble Codes
50001 146
Body Electrical > RR-Door Motor > Trouble Codes
50001 145
OK:

DTC B2311 is not output.



Result:
Result Proceed to
Any D-Door Motor DTCs in the table below are output A
Any P-Door Motor DTCs in the table below are output B
Any RL-Door Motor DTCs in the table below are output C
Any RR-Door Motor DTCs in the table below are output D
No DTCs in the table below are output E


Malfunction Status System Related DTCs
Power Window Motor Malfunction D-Door Motor B2311 Power Window Motor Malfunction
P-Door Motor B2311 Power Window Motor Malfunction
RL-Door Motor B2311 Power Window Motor Malfunction
RR-Door Motor B2311 Power Window Motor Malfunction


A

2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - AUXILIARY BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door) - AUXILIARY BATTERY AND BODY GROUND)

C

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door) - AUXILIARY BATTERY AND BODY GROUND)

D

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door) - AUXILIARY BATTERY AND BODY GROUND)

E

2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - AUXILIARY BATTERY AND BODY GROUND)
a.
B474751C27
1.51,0.385 1.917,0.635 0.406,0.25 1.063,1.115 1.542,1.115 true 1.854,1.135 2.396,1.135 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.625,0.427 1.938,0.625 0.313,0.198 10 false K7 0.917,1.042 1.229,1.24 0.313,0.198 10 false B 2.469,1.063 2.781,1.26 0.313,0.198 10 false GND
*a Component with harness connected
(Power Window Regulator Motor Assembly (for Driver Door))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K7-2 (B) - Body ground Ignition switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door) - AUXILIARY BATTERY AND BODY GROUND)
a.
B474753C25
1.458,0.344 1.906,0.625 0.448,0.281 0.979,1.135 1.531,1.135 true 1.875,1.135 2.427,1.135 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 0.844,1.052 1.156,1.25 0.313,0.198 10 false B 2.479,1.073 2.792,1.271 0.313,0.198 10 false GND 1.604,0.406 1.917,0.604 0.313,0.198 10 false L7
*a Component with harness connected
(Power Window Regulator Motor Assembly (for Front Passenger Door))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L7-2 (B) - Body ground Ignition switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door) - AUXILIARY BATTERY AND BODY GROUND)
a.
B474754C19
1.479,0.375 1.917,0.646 0.438,0.271 0.896,1.135 1.531,1.135 true 1.885,1.135 2.521,1.135 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.615,0.427 1.927,0.625 0.313,0.198 10 false N4 0.771,1.063 1.083,1.26 0.313,0.198 10 false B 2.583,1.052 3,1.271 0.417,0.219 10 false GND
*a Component with harness connected
(Power Window Regulator Motor Assembly (for Rear LH Door))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N4-2 (B) - Body ground Ignition switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door) - AUXILIARY BATTERY AND BODY GROUND)
a.
B474755C19
1.469,0.365 1.854,0.604 0.385,0.24 0.896,1.135 1.531,1.135 true 1.875,1.135 2.479,1.135 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 1.573,0.396 1.885,0.594 0.313,0.198 10 false M4 0.76,1.063 1.073,1.26 0.313,0.198 10 false B 2.542,1.073 2.854,1.271 0.313,0.198 10 false GND
*a Component with harness connected
(Power Window Regulator Motor Assembly (for Rear RH Door))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M4-2 (B) - Body ground Ignition switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)
a.

Perform the Active Test according to the display on the GTS.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -
Body Electrical > P-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -
Body Electrical > RL-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -
Body Electrical > RR-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -
Body Electrical > D-Door Motor > Active Test
Tester Display
Power Window
50004 124 1
Body Electrical > P-Door Motor > Active Test
Tester Display
Power Window
50004 144 1
Body Electrical > RL-Door Motor > Active Test
Tester Display
Power Window
50004 146 1
Body Electrical > RR-Door Motor > Active Test
Tester Display
Power Window
50004 145 1
OK:

Each power window operates normally.



Result:
Result Proceed to
OK A
NG (Driver door power window) B
NG (Front passenger door power window) C
NG (Rear LH door power window) D
NG (Rear RH door power window) E



A

7.PERFORM INITIALIZATION (APPLICABLE LOCATION)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

E

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

7.PERFORM INITIALIZATION (APPLICABLE LOCATION)
a.

Initialize the power window regulator motor assembly.

HINT:

Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

8.CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION)
8.CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION)
a.

Check that the power window operates normally by opening and closing it.

HINT:

Check the power window operation of the window where DTC B2311 has been stored.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK


OK:

Each power window operates normally.



Result:
Result Proceed to
OK A
NG (Driver door power window) B
NG (Front passenger door power window) C
NG (Rear LH door power window) D
NG (Rear RH door power window) E



A

9.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

E

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

9.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.

OK:

Power window components are installed correctly.



Result:
Proceed to
OK
NG



OK

10.CHECK DTC OUTPUT

NG

INSTALL PARTS CORRECTLY

10.CHECK DTC OUTPUT
a.

Turn the ignition switch off.


b.

Wait for at least 10 seconds, and then turn the ignition switch ON.


c.

Check for DTCs.

Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144
Body Electrical > RL-Door Motor > Trouble Codes
50001 146
Body Electrical > RR-Door Motor > Trouble Codes
50001 145
OK:

B2311 is not output.



Result:
Result Proceed to
OK A
NG (Driver door power window) B
NG (Front passenger door power window) C
NG (Rear LH door power window) D
NG (Rear RH door power window) E



A

END

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

E

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)