Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door) › 2020.03–2020.07
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0427204 POWER WINDOW REGULATOR MOTOR(for Rear Door) A

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the power window regulator motor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Door window regulator sub-assembly

·

Power window regulator motor assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Catch protection function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 67673A 3.REMOVE REAR DOOR FRAME GARNISH

Hide 84810D 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Hide 67603 5.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68173B 6.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

Hide 68196B 7.REMOVE REAR DOOR BELT FRONT SEAL

Hide 68198 8.REMOVE REAR DOOR BELT REAR SEAL

Hide 67841E 9.REMOVE REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

Hide 67841E 10.REMOVE REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

Hide 68142C 11.REMOVE REAR DOOR GLASS RUN

Hide 67407E 12.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 68103 13.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 14.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

Hide 85710F 15.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B563169

Remove the 3 bolts and power window regulator motor assembly.

NOTICE:
B572486C01
2.063,1.333 2.208,1.844 false 1.813,1.083 2.323,0.823 true 2.146,1.896 2.458,2.094 0.313,0.198 10 false *a 2.375,0.719 2.688,0.917 0.313,0.198 10 false *b
*a Protective Tape
*b Drum


Using a screwdriver with its tip wrapped in protective tape, carefully remove the power window regulator motor assembly while holding down the drum.