Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B000111  Driver Frontal Stage 1 Deployment Control Circuit Short to Ground  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B000111 Driver Frontal Stage 1 Deployment Control Circuit Short to Ground
·

The airbag sensor assembly detects a short to ground in the driver seat airbag squib circuit for 0.5 seconds

·

Spiral cable sub-assembly malfunction

·

Horn button assembly malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Spiral cable sub-assembly

·

Horn button assembly

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

B475053E70
4.948,1.344 5.333,1.625 0.385,0.281 10 false D+ 4.948,1.896 5.333,2.177 0.385,0.281 10 false D- 4.771,1.344 5.156,1.625 0.385,0.281 10 false 6 4.771,1.896 5.156,2.177 0.385,0.281 10 false 7 4.917,2.917 5.427,3.219 0.51,0.302 10 false H14 4.917,3.083 6.594,3.427 1.677,0.344 10 false Airbag Sensor Assembly 3.208,1.438 3.719,1.74 0.51,0.302 10 false H38 3.208,2 3.719,2.302 0.51,0.302 10 false H38 3.302,1.229 3.813,1.531 0.51,0.302 10 false 1 3.302,1.781 3.813,2.083 0.51,0.302 10 false 2 2.25,2.406 4.146,2.823 1.896,0.417 10 false Spiral Cable Sub-assembly 2.917,1.344 3.302,1.625 0.385,0.281 10 false D+ 2.948,1.896 3.333,2.177 0.385,0.281 10 false D- 2.135,1.427 2.646,1.729 0.51,0.302 10 false z3 2.135,1.99 2.646,2.292 0.51,0.302 10 false z3 0.865,2.417 1.688,3.344 0.823,0.927 10 false Horn Button Assembly 2.177,1.229 2.688,1.531 0.51,0.302 10 false 2 2.177,1.781 2.688,2.083 0.51,0.302 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

To perform the simulation method, select Check Mode with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK CURRENT DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Post-procedure1

c.

None


Result:
Result Proceed to
Current B000111 is output A
History B000111 is output B



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag sensor assembly.

OK:

The connectors are properly connected.



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C422856C02
1.979,1.094 1.979,1.479 false 0.271,1.083 0.271,1.469 false 0.208,1.49 0.729,1.844 0.521,0.354 10 false *1 1.031,0.948 1.333,1.25 0.302,0.302 10 false *2 2.75,0.948 3.083,1.25 0.333,0.302 10 false *3 1.906,1.49 2.323,1.792 0.417,0.302 10 false *4
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Wire Harness


Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag sensor assembly.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanisms of the wire harness connector and spiral cable sub-assembly connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

4.CHECK HORN BUTTON ASSEMBLY

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY OR REPAIR OR REPLACE WIRE HARNESS

4.CHECK HORN BUTTON ASSEMBLY
a.
C422838C02
0.427,2.156 0.74,2.375 0.313,0.219 1.99,2.344 1.74,2.344 false 1.281,2.396 0.865,2.854 true 0.313,0.76 0.313,1.177 false 0.24,1.198 0.635,1.5 0.396,0.302 10 false *1 1.135,0.604 1.406,0.865 0.271,0.26 10 false *2 2.719,0.604 3.167,0.958 0.448,0.354 10 false *3 0.302,1.677 0.698,2.167 0.396,0.49 10 false *a 0.698,2.771 0.927,3.042 0.229,0.271 10 false *b 2.021,2.25 2.323,2.479 0.302,0.229 10 false SST 0.5,2.167 0.781,2.396 0.281,0.229 10 false z3 2.333,0.604 2.531,0.833 0.198,0.229 10 false A 2.177,0.604 2.313,0.865 0.135,0.26 10 false B 1.75,0.604 1.885,0.844 0.135,0.24 10 false C 1.594,0.604 1.74,0.917 0.146,0.313 10 false D 0.75,0.604 0.875,0.813 0.125,0.208 10 false E 0.438,0.604 0.594,0.844 0.156,0.24 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Connect the connectors to the airbag sensor assembly and spiral cable sub-assembly.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector E (light green connector).

CAUTION:

Never connect a tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.CHECK HORN BUTTON ASSEMBLY
5.CHECK HORN BUTTON ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B000111 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B000111 is not output A
B000111 is output B


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Disconnect SST from connector E.



A

B

6.CHECK DRIVER SEAT AIRBAG SQUIB CIRCUIT (SHORT TO GROUND)
6.CHECK DRIVER SEAT AIRBAG SQUIB CIRCUIT (SHORT TO GROUND)

Pre-procedure1

a.
C422839C02
0.51,2.229 0.865,2.49 0.354,0.26 0.25,1.208 0.25,0.875 false 1.875,2.813 1.406,2.438 true 1.917,1.208 1.917,0.875 false 1.833,1.24 2.125,1.5 0.292,0.26 10 false *4 1.073,0.698 1.375,1.042 0.302,0.344 10 false *2 2.813,0.74 3.146,1.229 0.333,0.49 10 false *3 0.323,1.698 0.625,2.042 0.302,0.344 10 false *a 2.375,0.708 2.708,1.198 0.333,0.49 10 false A 2.052,0.708 2.385,1.198 0.333,0.49 10 false B 1.708,0.708 2.042,1.198 0.333,0.49 10 false C 1.542,0.708 1.698,1.188 0.156,0.479 10 false D 0.698,0.719 0.865,1 0.167,0.281 10 false E 0.375,0.719 0.573,1.063 0.198,0.344 10 false F 0.604,2.26 0.896,2.5 0.292,0.24 10 false z3 1.927,2.74 2.271,3.021 0.344,0.281 10 false *b 0.167,1.24 0.458,1.5 0.292,0.26 10 false *1
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Wire Harness
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Disconnect the connector from the airbag sensor assembly.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 - Body ground Always 1 MΩ or higher
z3-1 - Body ground Always 1 MΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

9.CHECK WIRE HARNESS (SHORT TO GROUND)
7.CLEAR DTC
a.
C422840C02
0.271,1.156 0.271,1.49 false 0.219,1.51 0.5,1.813 0.281,0.302 10 false *1 0.417,0.99 0.552,1.26 0.135,0.271 10 false F 0.573,0.99 0.729,1.25 0.156,0.26 10 false E 1.5,0.99 1.646,1.323 0.146,0.333 10 false D 1.656,0.99 1.813,1.271 0.156,0.281 10 false C 2.094,0.99 2.25,1.323 0.156,0.333 10 false B 2.25,0.99 2.427,1.25 0.177,0.26 10 false A 1,0.99 1.49,1.635 0.49,0.646 10 false *2 2.667,1 2.979,1.344 0.313,0.344 10 false *3
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly


Connect the connectors to the horn button assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B000111 may be output at this time, but they are not related to this check.



Post-procedure1

c.

None


Result:
Result Proceed to
B000111 is not output A
B000111 is output B



A

USE SIMULATION METHOD TO CHECK

B

9.CHECK WIRE HARNESS (SHORT TO GROUND)

Pre-procedure1

a.
C422841C02
0.427,2.406 0.875,2.667 0.448,0.26 2.01,0.958 2.01,1.24 false 1.271,2.594 1.021,2.969 true 1.448,2.594 1.698,2.969 true 0.271,0.948 0.271,1.229 false 0.531,2.448 0.865,2.635 0.333,0.188 10 false H38 0.385,0.792 0.573,1.198 0.188,0.406 10 false F 0.656,0.792 0.896,1.25 0.24,0.458 10 false E 1.479,0.792 1.802,1.063 0.323,0.271 10 false D 1.75,0.792 1.906,1.031 0.156,0.24 10 false C 2.104,0.792 2.26,1.052 0.156,0.26 10 false B 2.365,0.792 2.531,1.073 0.167,0.281 10 false A 1.042,0.802 1.302,1.083 0.26,0.281 10 false *2 0.208,1.24 0.667,1.583 0.458,0.344 10 false *1 2.74,0.802 3.063,1.115 0.323,0.313 10 false *3 0.344,1.969 0.719,2.313 0.375,0.344 10 false *a 1.677,2.99 2.083,3.25 0.406,0.26 10 false D- 1.958,1.24 2.292,1.521 0.333,0.281 10 false *4 0.938,2.99 1.333,3.24 0.396,0.25 10 false D+
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Wire Harness
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the connector from the spiral cable sub-assembly.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H38-1 (D+) - Body ground Always 1 MΩ or higher
H38-2 (D-) - Body ground Always 1 MΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR