Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0420500 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B232588  Door LIN Bus off  


DESCRIPTION

If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more, DTC B232588 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B232588 Door LIN Bus off The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Front power window regulator motor assembly RH

·

Front power window regulator motor assembly LH

·

Rear power window regulator motor assembly RH

·

Rear power window regulator motor assembly LH

·

Wire harness or connector



WIRING DIAGRAM

C436188E02
1.552,4.552 1.792,4.771 0.24,0.219 10 false LIN 1.479,2.219 1.854,2.417 0.375,0.198 10 false LIN2 5.427,1.865 5.813,2.073 0.385,0.208 10 false LIN2 1.563,6.771 1.802,6.99 0.24,0.219 10 false LIN 5.396,6.771 5.969,7.115 0.573,0.344 10 false LIN 5.417,4.531 5.656,4.75 0.24,0.219 10 false LIN 5.344,3.156 7.01,3.542 1.667,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 5.063,5.125 6.99,5.542 1.927,0.417 10 false Front Power Window Regulator Motor Assembly LH 0.448,2.677 2.063,3.208 1.615,0.531 10 false Multiplex Network Master Switch Assembly 0.365,5.094 2.292,5.531 1.927,0.438 10 false Front Power Window Regulator Motor Assembly RH 5.021,7.333 6.917,7.802 1.896,0.469 10 false Rear Power Window Regulator Motor Assembly RH 0.417,7.323 2.313,7.844 1.896,0.521 10 false Rear Power Window Regulator Motor Assembly LH 1.479,1.885 1.823,2.104 0.344,0.219 10 false LIN1 0.625,8.333 2.552,8.635 1.927,0.302 10 false : LIN Communication Line 0.458,2.521 0.896,2.771 0.438,0.25 10 false K5 5.083,4.958 5.698,5.271 0.615,0.313 10 false L7 5.021,7.167 5.938,7.438 0.917,0.271 10 false M4 0.427,7.146 0.865,7.396 0.438,0.25 10 false N4 0.375,4.927 0.813,5.177 0.438,0.25 10 false K7 5.333,2.969 5.771,3.219 0.438,0.25 10 false MB 4.052,1.875 4.49,2.125 0.438,0.25 10 false 4E 5.146,1.729 5.583,1.979 0.438,0.25 10 false 15 4.042,1.688 4.479,1.938 0.438,0.25 10 false 17 1.865,1.698 2.302,1.948 0.438,0.25 10 false 17 5.198,4.396 5.635,4.646 0.438,0.25 10 false 9 1.875,4.406 2.313,4.656 0.438,0.25 10 false 9 1.865,6.615 2.302,6.865 0.438,0.25 10 false 9 5.219,6.625 5.656,6.875 0.438,0.25 10 false 9 1.875,2.063 2.313,2.313 0.438,0.25 10 false 16 4.063,2.823 5.198,3.24 1.135,0.417 10 false Power Distribution Box Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232588 is not output B



A

3.CLEAR DTC

B

3.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the K7 front power window regulator motor assembly RH connector.


b.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232187 is not output B



A

5.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

5.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

6.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
6.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Disconnect the K7 multiplex network master switch assembly connector.


b.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B120687 and B232187 is not output B



A

7.CLEAR DTC

B

15.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR WITH MOTOR ASSEMBLY RH)
7.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

8.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
8.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the L7 front power window regulator motor assembly LH connector.


b.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232587 is output A
DTC B232287 is not output B



A

9.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

9.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

10.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
10.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the M4 rear power window regulator motor assembly RH connector.


b.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232587 is output A
DTC B232387 is not output B



A

11.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

11.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

12.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
12.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the N4 rear power window regulator motor assembly LH connector.


b.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232587 is output A
DTC B232487 is not output B



A

13.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

13.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the power distribution box assembly connector.


c.

Disconnect the K7 front door window regulator with motor assembly RH connector.


d.

Disconnect the L7 front door window regulator with motor assembly LH connector.


e.

Disconnect the M4 rear door window regulator with motor assembly RH connector.


f.

Disconnect the N4 rear door window regulator with motor assembly LH connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-15 (LIN2) - Body ground Always 10 kΩ or higher
MB-15 (LIN2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

14.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
14.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K7 front door window regulator with motor assembly RH connector.


c.

Disconnect the L7 front door window regulator with motor assembly LH connector.


d.

Disconnect the M4 rear door window regulator with motor assembly RH connector.


e.

Disconnect the N4 rear door window regulator with motor assembly LH connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - Body ground Always 10 kΩ or higher
4E-17 - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR WITH MOTOR ASSEMBLY RH)
a.

Disconnect the K5 multiplex network master switch assembly connector.


b.

Disconnect the K7 front door window regulator with motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K5-16 (LIN2) or K7-9 (LIN) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR