52618
1.INSTALL FRONT BUMPER LOWER ABSORBER
Install the 4 grommets.
Engage the claws to install the front bumper lower absorber.
| *a | screw |
| *b | clip |
Install the clip and 7 screws.
51451A
2.INSTALL CENTER ENGINE UNDER COVER
57014C
3.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH
If install a new front side member bracket sub-assembly LH:
Temporarily install the front side member bracket sub-assembly LH with the 5 bolts until the "reference value" and " point-to-point distance" are aligned.
Vehicle Exterior > BODY PANEL > RADIATOR SUPPORT > REFERENCE VALUE
Vehicle Exterior > BODY DIMENSIONS > ENGINE COMPARTMENT REFERENCE VALUES > POINT-TO-POINT DISTANCE
If reusing the front side member bracket sub-assembly LH:
Temporarily install the front side member bracket sub-assembly LH with the 5 bolts until the matchmarks are aligned.
Tighten the 5 bolts.
Engage the clamp.
57013D
4.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH
If install a new front side member bracket sub-assembly RH:
Temporarily install the front side member bracket sub-assembly RH with the 5 bolts until the "reference value" and " point-to-point distance" are aligned.
Vehicle Exterior > BODY PANEL > RADIATOR SUPPORT > REFERENCE VALUE
Vehicle Exterior > BODY DIMENSIONS > ENGINE COMPARTMENT REFERENCE VALUES > POINT-TO-POINT DISTANCE
If reusing the front side member bracket sub-assembly RH:
Temporarily install the front side member bracket sub-assembly RH with the 5 bolts until the matchmarks are aligned.
Tighten the 5 bolts.
16595D
5.INSTALL NO. 1 RADIATOR AIR GUIDE LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the claws to Install the No. 1 radiator air guide LH as shown in the illustration.
16561D
6.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the claws to install the No. 1 radiator to support seal as shown in the illustration.
7.INSTALL NO. 2 RADIATOR TO SUPPORT SEAL
for Gasoline Model:
|
Install in this Direction |
Engage the claws to install the No. 2 radiator to support seal as shown in the illustration.
for HV Model:
|
Install in this Direction |
Engage the claws to install the No. 2 radiator to support seal as shown in the illustration.
16695A
8.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE LH
|
Install in this Direction |
Engage the claws to install the front radiator side air guide plate LH as shown in the illustration.
16691A
9.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE RH
|
Install in this Direction |
Engage the claws to install the front radiator side air guide plate RH as shown in the illustration.
52131A
10.INSTALL FRONT BUMPER REINFORCEMENT
Install the front bumper reinforcement with 8 bolts and 2 nuts.
Engage the wire harness clamps.
88790B
11.INSTALL THERMISTOR ASSEMBLY
Engage the clamps to install the thermistor assembly.
52611
12.INSTALL FRONT BUMPER ENERGY ABSORBER
Engage the guides to install the front bumper energy absorber.
16681A
13.INSTALL RADIATOR UPPER AIR GUIDE PLATE
Engage the clips to install the radiator upper air guide plate.
Engage the wire harness clamp.
52536
14.INSTALL FRONT BUMPER SIDE RETAINER LH
Engage the 2 claws to install the front bumper side retainer LH.
52535
15.INSTALL FRONT BUMPER SIDE RETAINER RH
Use the same procedure as for the LH side.
16.INSTALL HEADLIGHT ASSEMBLY LH
for Halogen Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Halogen Headlight)>INSTALLATION
for LED Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>INSTALLATION
17.INSTALL HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
53879H
18.INSTALL FRONT FENDER LINER RETAINER
Engage the claw to install the front fender liner retainer.
Use the same procedure for the RH side and LH side.
53112A
19.INSTALL LOWER RADIATOR GRILLE
Engage the claws to install the lower radiator grille.
Install the 3 screws.
53101
20.INSTALL RADIATOR GRILLE SUB-ASSEMBLY
Install the 2 nuts.
Engage the claws to install the radiator grille sub-assembly.
Install the 4 clips and 2 screws.
53155D
21.INSTALL NO. 1 RADIATOR GRILLE SEAL
Engage the claws to install the No. 1 radiator grille seal.
Install the 2 screws.
53395E
22.INSTALL HOOD TO FRONT END PANEL SEAL
Engage the clips to install the hood to front end panel seal.
52129D
23.INSTALL FRONT BUMPER LOWER COVER
Engage the hook to install the front bumper lower cover.
Engage the claws.
52127C
24.INSTALL FRONT BUMPER HOLE COVER
Engage the hook to install the front bumper hole cover.
Engage the claws.
52113D
25.INSTALL FRONT BUMPER EXTENSION LH
Engage the claws to install the front bumper extension LH.
52112D
26.INSTALL FRONT BUMPER EXTENSION RH
Use the same procedure as for the LH side.
27.INSTALL WIRING HARNESS CONNECTOR (w/o Parking Support Brake System)
Engage the clamp to install the wiring harness connector.
75311
28.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
| *a | Heated Part |
| *b | Heat Light |
When installing the radiator grille (or front panel) emblem, heat the front bumper assembly and radiator grille (or front panel) emblem a heat light.
| Item | Temperature |
|---|---|
·
Front Bumper Assembly ·
Radiator Grille (or front panel) Emblem |
20 to 30°C (68 to 86°F) |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front bumper assembly and radiator grille (or front panel) emblem excessively.
| *a | Location Pin |
Clean the front bumper assembly surface.
Using a heat light, heat the front bumper assembly surface.
Remove any remaining double-sided tape from the front bumper assembly.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the front bumper assembly and a new radiator grille (or front panel) emblem.
Remove the release paper from the radiator grille (or front panel) emblem.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Engage the location pins and install the radiator grille (or front panel) emblem as shown in the illustration.
82113
29.INSTALL NO. 3 ENGINE ROOM WIRE (w/ Wire Harness)
w/ Parking Support Brake System:
Engage the clamps to install the No. 3 engine room wire.
w/o Parking Support Brake System:
Engage the clamps to install the No. 3 engine room wire.
88211B
30.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY
89347B
31.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)
89341L
32.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ Parking Support Brake System)
89341K
33.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ Parking Support Brake System)
89348N
34.INSTALL NO. 1 ULTRASONIC SENSOR CLIP (w/ Parking Support Brake System)