Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › 2020.03–2020.07
RM36W0E _53 Suspension _087263 FRONT SUSPENSION _0417616 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 48811 1.INSTALL FRONT STABILIZER BAR

Hide 2.INSTALL STEERING LINK ASSEMBLY

Hide 48069 3.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C428575

Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.


Hide 48068 4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 12363A 5.INSTALL ENGINE MOVING CONTROL ROD

a.

Install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.

Torque:
200 N*m (2039 kgf*cm, 148 ft.*lbf)


Hide 51201 6.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Slowly jack up the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

CAUTION:
C320210

·

The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:
·

Use attachments to keep the front suspension crossmember sub-assembly level.

·

Make sure that the front suspension crossmember sub-assembly dose not hit the protrusion of the reinforcement.

·
C430482C01
0.583,1.948 0.885,2.177 0.302,0.229 10 true *a 2.385,1.948 2.688,2.177 0.302,0.229 10 true *b
*a OK
*b NG


After installation, check that the claws of the steering column hole cover base are not disengaged.




b.
C432279N01
0.552,1.302 0.708,1.5 0.156,0.198 10 true A 2.719,1.333 2.875,1.531 0.156,0.198 10 true A 0.656,1.604 0.813,1.802 0.156,0.198 10 true A 2.635,1.604 2.792,1.802 0.156,0.198 10 true A 0.552,1.958 0.708,2.156 0.156,0.198 10 true A 2.74,1.948 2.896,2.146 0.156,0.198 10 true A 2.198,0.385 2.354,0.583 0.156,0.198 10 true A 1.094,0.365 1.25,0.563 0.156,0.198 10 true A 0.333,0.094 0.49,0.292 0.156,0.198 10 true B 2.958,0.104 3.115,0.302 0.156,0.198 10 true B

Install the front suspension crossmember sub-assembly to the vehicle body with the 8 bolts (A).

Torque:
107.5 N*m (1096 kgf*cm, 79 ft.*lbf)


c.

Install the 2 bolts (B).

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


d.

Lower the engine lifter.


e.

Install the engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


f.

Install the wiring harness clamp bracket to the front suspension crossmember sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 48069 7.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 8.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 9.CONNECT TIE ROD END SUB-ASSEMBLY LH

a.
C398436

Connect the tie rod end sub-assembly LH to the steering knuckle LH with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Do not damage the ball joint dust cover.

·

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.




b.

Install a new cotter pin.


Hide 45046 10.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 11.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the front stabilizer link assembly LH to the front stabilizer bar with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 12.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53876A 13.INSTALL FRONT FENDER LINER LH

a.

Install the front fender liner LH to the vehicle body with the 2 screws.


Hide 53875A 14.INSTALL FRONT FENDER LINER RH

HINT:

Perform the same procedure as for the LH side.


Hide 15.INSTALL FRONT WHEELS

Hide 45260 16.CONNECT NO.2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 17.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 48069 19.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 20.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

Hide 51447D 21.INSTALL CENTER NO. 4 ENGINE UNDER COVER

a.

Install the center No. 4 engine under cover to the vehicle with the 2 bolts and 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51442C 22.INSTALL ENGINE UNDER COVER LH

a.

Install the engine under cover LH to the vehicle with the 2 clips.


Hide 51441C 23.INSTALL ENGINE UNDER COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 51451A 24.INSTALL CENTER ENGINE UNDER COVER

a.

Install the center engine under cover to the vehicle with the 4 bolts, 4 screws and 9 clips.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 25.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 26.PERFORM INITIALIZATION

Parking support brake system (Click here)
Parking assist monitor system (Click here)