Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › INPUT SHAFT OIL SEAL › 2020.03–2020.07
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0421994 INPUT SHAFT OIL SEAL A

P910 HYBRID TRANSMISSION / TRANSAXLE  INPUT SHAFT OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during input shaft type T oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
ECM Perform Vehicle Identification Number (VIN) registration DTC P063051 is output (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
·

Engine assembly

·

Air fuel ratio sensor

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 30900 1.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 35710A 2.REMOVE INPUT SHAFT TYPE T OIL SEAL

a.
C429488C02
2.042,1.635 1.135,0.5 1.135,0.5 0.979,0.5 true 0.75,0.417 1.063,0.615 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the input shaft type T oil seal from the hybrid vehicle transaxle assembly.

NOTICE:

Be careful not to damage the input shaft assembly or hybrid vehicle transaxle assembly.



Hide 35710A 3.INSTALL INPUT SHAFT TYPE T OIL SEAL

a.

Coat the lip of a new input shaft type T oil seal with a small amount of MP grease.


b.
C429489C02
1.854,1.948 2.229,3 2.229,3 2.385,3 true 1.427,0.094 1.708,0.313 0.281,0.219 10 false *a 2.448,2.906 2.813,3.115 0.365,0.208 10 false SST
*a Depth


Using SST and a hammer, install the input shaft type T oil seal to the hybrid vehicle transaxle assembly.

SST
09388-40010  

Standard Depth:

1.0 to 1.8 mm (0.0394 to 0.0709 in.)


NOTICE:
·

Do not allow foreign matter to attach to the lip of the input shaft type T oil seal.

·

Do not install the input shaft type T oil seal at an angle.




Hide 30900 4.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY