Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0422037 BRAKE SYSTEM(for HV Model) G

BRAKE SYSTEM (OTHER)  BRAKE SYSTEM(for HV Model)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

DTCs may be stored during the inspection procedure. Be sure to clear the DTCs and check that no DTCs are output after the inspection is finished.


PROCEDURE

Hide 1.INSPECT PRESSURE SENSOR

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the ignition switch is off)



b.

Set a pedal effort gauge, SST and connect the GTS.

i.
C429588C02
0.635,0.313 0.885,0.313 false 1.823,0.313 2.073,0.313 false 2.521,0.281 2.771,0.281 false 0.25,3.333 0.302,3.219 false 3.198,2.802 3.198,2.99 false 2.115,0.219 2.427,0.375 0.313,0.156 10 false *a 0.948,0.219 1.26,0.375 0.313,0.156 10 false *b 0.073,3.313 0.385,3.469 0.313,0.156 10 false *c 3.146,3.021 3.354,3.219 0.208,0.198 10 false *c 2.313,0.177 2.625,0.333 0.313,0.156 10 false *b
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060)


ii.

Connect the GTS to the DLC3 with the ignition switch off, park (P) selected and parking brake applied.


iii.

Turn the ignition switch to ON and turn the GTS on.


iv.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING



c.

Inspect the reaction force pressure and servo pressure.

i.

Enter the following menus: Chassis / Brake / Data List / Reaction Force Pressure and Servo Pressure.

Chassis > Brake > Data List
Tester Display
Reaction Force Pressure
Servo Pressure
50003 435 205,210

ii.

Check the value output from "Reaction Force Pressure" and "Servo Pressure" by depressing the brake pedal.

Standard Result:
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.15 to 0.95 2.4 to 6.4 2.1 to 6.1 MPa (21.4 to 62.2 kgf/cm2, 305 to 885 psi) 2.1 to 6.1 MPa (21.4 to 62.2 kgf/cm2, 305 to 885 psi)
100 N (10 kgf, 22.5 lbf) 0.95 to 1.75 6.6 to 10.6 6.3 to 10.3 MPa (64.2 to 105.0 kgf/cm2, 914 to 1494 psi) 6.3 to 10.3 MPa (64.2 to 105.0 kgf/cm2, 914 to 1494 psi)
150 N (15 kgf, 33.7 lbf) 1.42 to 2.22 6.8 to 10.8 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi)
200 N (20 kgf, 45.0 lbf) 2.11 to 2.91 6.8 to 10.8 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi)


Standard Result:
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Left Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.15 to 0.95 2.4 to 6.4 2.1 to 6.1 MPa (21.4 to 62.2 kgf/cm2, 305 to 885 psi) 2.1 to 6.1 MPa (21.4 to 62.2 kgf/cm2, 305 to 885 psi)
100 N (10 kgf, 22.5 lbf) 0.95 to 1.75 6.6 to 10.6 6.3 to 10.3 MPa (64.2 to 105.0 kgf/cm2, 914 to 1494 psi) 6.3 to 10.3 MPa (64.2 to 105.0 kgf/cm2, 914 to 1494 psi)
150 N (15 kgf, 33.7 lbf) 1.42 to 2.22 6.8 to 10.8 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi)
200 N (20 kgf, 45.0 lbf) 2.11 to 2.91 6.8 to 10.8 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi)




d.

Remove the pedal effort gauge and SST.

i.

Remove the pedal effort gauge and SST, and bleed the brake line.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING



e.

Inspect the accumulator pressure.

i.

Enter the following menus: Chassis / Brake / Data List / Accumulator Pressure and MT Voltage Value.

Chassis > Brake > Data List
Tester Display
MT Voltage Value
Accumulator Pressure
50003 435 34,212

ii.

While fully depressing the brake pedal 4 or 5 times, check that the MT voltage value is 10 V or more once or more.

HINT:

Usually the MT voltage value is 0 V.



iii.

After confirming that the booster pump motor stops, check the accumulator pressure.

Standard Result:

15 to 21 MPa




Hide 47210L 2.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the ignition switch is off)



b.

Set a pedal effort gauge, SST and connect the GTS.

i.
C429588C03
0.635,0.313 0.885,0.313 false 1.823,0.313 2.073,0.313 false 2.521,0.281 2.771,0.281 false 0.25,3.333 0.302,3.219 false 3.198,2.802 3.198,2.99 false 2.115,0.219 2.427,0.375 0.313,0.156 10 false *a 0.948,0.219 1.26,0.375 0.313,0.156 10 false *b 0.073,3.313 0.385,3.469 0.313,0.156 10 false *c 3.146,3.021 3.354,3.219 0.208,0.198 10 false *c 2.313,0.177 2.625,0.333 0.313,0.156 10 false *b
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060)


ii.

Connect the GTS to the DLC3 with the ignition switch off, park (P) selected and parking brake applied.


iii.

Turn the ignition switch to ON and turn the GTS on.



v.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING



c.

Check operation without the brake booster.

i.

Inspect and adjust the brake pedal height.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for HV Model)>ADJUSTMENT


ii.
C429589C04
1.073,1.49 1.656,1.49 true 1.073,1.229 1.656,1.229 true 0.781,1.125 1,1.313 0.219,0.188 10 true *a 0.781,1.396 1,1.583 0.219,0.188 10 true *b
*a Fluid Level Support Line
*b MIN Line


Adjust the brake fluid level in the reservoir between MIN line and fluid level support line.


iii.

Turn the GTS on and enter the following menus: Chassis / Brake / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > Brake > Utility
Tester Display
ECB Utility
50005 435 2617

iv.

Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


v.

Perform "Motor Invalid" according to the display on the GTS.


vi.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



vii.

Check that the brake pedal is firm.


viii.

Enter the following menus: Chassis / Brake / Data List / Stroke Sensor and Stroke Sensor 2.

Chassis > Brake > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 435 207,208

ix.

Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Result:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.24 to 1.94 3.06 to 3.76 0.06 to 2.06 MPa (0.6 to 21.0 kgf/cm2, 9 to 299 psi) 0.06 to 2.06 MPa (0.6 to 21.0 kgf/cm2, 9 to 299 psi)
500 N (51 kgf, 112.4 lbf) 1.41 to 2.11 2.89 to 3.59 2.09 to 4.09 MPa (21.3 to 41.7 kgf/cm2, 303 to 593 psi) 2.09 to 4.09 MPa (21.3 to 41.7 kgf/cm2, 303 to 593 psi)


Standard Result:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.24 to 1.94 3.06 to 3.76 0.06 to 2.06 MPa (0.6 to 21.0 kgf/cm2, 9 to 299 psi) 0.06 to 2.06 MPa (0.6 to 21.0 kgf/cm2, 9 to 299 psi)
500 N (51 kgf, 112.4 lbf) 1.41 to 2.11 2.89 to 3.59 2.09 to 4.09 MPa (21.3 to 41.7 kgf/cm2, 303 to 593 psi) 2.09 to 4.09 MPa (21.3 to 41.7 kgf/cm2, 303 to 593 psi)



x.

Remove the pedal effort gauge and SST, and bleed the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING


xi.

Enter the following menus: Chassis / Brake / Data List / Accumulator Pressure, and check the output pressure.

Standard Result:

15 to 21 MPa


Chassis > Brake > Data List
Tester Display
Accumulator Pressure
50003 435 212



Hide 3.INSPECT STROKE SIMULATOR

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the ignition switch is off)



b.

Connect the GTS and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the GTS to the DLC3 with the ignition switch off, park (P) selected and parking brake applied.


iii.

Turn the ignition switch to ON and turn the GTS on.




c.

Check operation with the brake booster.

i.

Turn the ignition switch to ON.


ii.

Enter the following menus: Chassis / Brake / Data List / Stroke Sensor and Stroke Sensor 2.

Chassis > Brake > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 435 207,208

iii.

Depress the brake pedal 4 or 5 times.


iv.

Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
50 N (5 kgf, 11.2 lbf) 1.13 to 1.83 3.17 to 3.87
100 N (10 kgf, 22.5 lbf) 1.26 to 1.96 3.04 to 3.74
150 N (15 kgf, 33.7 lbf) 1.35 to 2.05 2.95 to 3.65