Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0422043 BRAKE PEDAL(for HV Model) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for HV Model)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Remove front door scuff plate RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


b.

Remove cowl side trim board RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


c.

Turn back tibia pad.


d.

Check the brake pedal height.

HINT:

Inspect and adjust the brake pedal height with the tibia pad folded back.


i.

Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.

C429810C02
5.948,1.052 6.177,0.844 false 2.698,1.573 2.813,1.938 true 0.958,1.406 1.188,1.594 0.229,0.188 10 true *a 2.771,1.948 3,2.135 0.229,0.188 10 true *1 5.969,1.76 6.198,1.948 0.229,0.188 10 true *a 6.219,0.76 6.448,0.948 0.229,0.188 10 true *1
*1 Brake Pedal Pad - -
*a Brake Pedal Height - -
V100155

Measuring Plane of Floor Panel - -


Brake Pedal Height from Floor Panel:

157.8 to 173.8 mm (6.21 to 6.84 in.)


If the pedal height is not as specified, adjust the brake pedal height according to the procedure below.



e.
C429811C01
2.344,1.292 2.656,1.292 false 1.625,1.781 1.625,2.156 false 1.896,3.906 1.385,4.167 true 2.708,1.229 3.021,1.385 0.313,0.156 10 false *1 1.542,2.188 1.854,2.344 0.313,0.156 10 false *2 2.323,3.552 2.635,3.708 0.313,0.156 10 false *a 1.198,4.115 1.51,4.271 0.313,0.156 10 false *3
*1 Stop Light Switch Assembly
*2 Clevis Lock Nut
*3 Floor Panel
*a Brake Pedal Height


Adjust the brake pedal height.

i.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Loosen the clevis lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Brake Pedal Height from Floor Panel:

157.8 to 173.8 mm (6.21 to 6.84 in.)



iv.

Tighten the clevis lock nut.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION



f.

Install the tibia pad to its original position.


g.

h.

Install front door scuff plate RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 89510D 2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.

Inspect the brake pedal stroke sensor assembly.

i.

Connect the GTS to the DLC3 with the ignition switch off.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on and enter the following menus: Chassis / Brake / Data List / Stroke Sensor.

Chassis > Brake > Data List
Tester Display
Stroke Sensor
50003 435 207

iv.

Read the stroke sensor value without the brake pedal depressed.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V


If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.



b.

Adjust the brake pedal stroke sensor assembly.


ii.
C431714

Loosen the 2 nuts.

NOTICE:

After turning the ignition switch to ON, do not depress the brake pedal until the nuts have been tightened.



iii.
C431715

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



iv.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


v.

Turn the GTS off and turn the ignition switch off.


vi.

Disconnect the GTS.




c.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


Hide 3.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708C04
2.177,1.542 2.781,1.885 0.604,0.344 10 *a
*a Brake Pedal Free Play


Depress the brake pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.

Brake Pedal Free Play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 4.INSPECT BRAKE PEDAL RESERVE DISTANCE

a.

Remove front door scuff plate RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


b.

Remove cowl side trim board RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


c.

Turn back tibia pad.


d.

With the ignition switch ON (READY), depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.

C429812C02
2.854,1.51 2.99,1.917 true 5.719,1.094 6.083,0.75 true 2.938,1.938 3.156,2.135 0.219,0.198 10 true *1 6.115,0.646 6.333,0.844 0.219,0.198 10 true *1 6.052,1.688 6.271,1.885 0.219,0.198 10 true *a 1.396,1.229 1.615,1.427 0.219,0.198 10 true *a
*1 Brake Pedal Pad - -
*a Brake Pedal Reserve Distance - -
V100155

Measuring Plane of Floor Panel - -


Brake Pedal Reserve Distance from Floor Panel at 300 N (31 kgf, 67.4 lbf):

101 mm (3.98 in.) or more


If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM (for HV Model)>PROBLEM SYMPTOMS TABLE


e.

Install the tibia pad to its original position.


f.

g.

Install front door scuff plate RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION