Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER › 2020.03–2020.07
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0422045 BRAKE MASTER CYLINDER A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER  INSTALLATION  


PROCEDURE

Hide 47201 1.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

NOTICE:

When installing a new brake master cylinder sub-assembly, remove the protectors from the master cylinder piston and outlet ports.


a.

Install a new brake master cylinder O-ring to the brake master cylinder sub-assembly.


b.

Install the brake master cylinder sub-assembly to the brake booster assembly with 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

The brake master cylinder sub-assembly requires careful handling. Do not drop or subject the brake master cylinder sub-assembly to any impact. Do not reuse a brake master cylinder sub-assembly that has been dropped.

·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its brake master cylinder reservoir assembly when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, or cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of cloth and then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




c.
C435046C01
1.781,3.042 2.094,3.198 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




d.

Connect the reservoir level switch connector.


Hide 31434E 2.CONNECT NO. 1 CLUTCH RESERVOIR HOSE (for Manual Transaxle)

a.
C435041C01
1.5,0.99 1.948,0.635 true 1.958,0.531 2.198,0.729 0.24,0.198 10 true *a
*a Paint Mark


Connect the No. 1 clutch reservoir hose to the brake master cylinder reservoir assembly and slide the clip to secure it.

NOTICE:

When connecting the No. 1 clutch reservoir hose, face the paint mark up.



Hide 4.BLEED CLUTCH LINE (for Manual Transaxle)

Hide 55701J 5.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55815E 7.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 8.INSTALL WINDSHIELD WIPER MOTOR AND LINK