Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0424496 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 1.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

a.

Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I116327C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Install the 6 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 55306A 3.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

NOTICE:

Do not fully tighten the screw.



Hide 4.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Tighten the 3 bolts, screws and nut in the order shown in the illustration to install the air conditioner unit assembly.

I116328N01
2.333,1.188 2.469,1.354 0.135,0.167 10 true 2 4.125,1.271 4.26,1.438 0.135,0.167 10 true 1 5.063,1.24 5.198,1.406 0.135,0.167 10 true 3 5.24,2.865 5.375,3.031 0.135,0.167 10 true 4 3.135,3.083 3.271,3.25 0.135,0.167 10 true 5

Torque:
Bolt : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 82141 5.INSTALL INSTRUMENT PANEL WIRE

a.

Engage clamps to install the instrument panel wire.

I116329


b.

Install the 4 ground wires with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

for Manual Air Conditioning System:

i.
I115686

Engage the clamp.


ii.

Connect the connector.



d.

for Automatic Air Conditioning System:

i.

Engage the clamp.


ii.
I116396

Connect the 2 connectors.



e.

for Manual Air Conditioning System:

i.
I115683

Engage the clamps.


ii.

Connect the 2 connectors.



f.

for Automatic Air Conditioning System:

i.
I115682

Engage the clamp.


ii.

Connect the connector.



g.
I115680

Install the instrument panel junction block assembly RH with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


h.
I115677

Engage the clamps.


Hide 6.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

Hide 83108 7.INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 88539J 8.INSTALL DRAIN COOLER HOSE

a.
I115675

Connect the drain cooler hose.


Hide 55216C 9.INSTALL NO. 4 DASH PANEL INSULATOR PAD

a.

Engage the clips to install the No. 4 dash panel insulator pad.

I116330


Hide 58510D 10.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.

Install the front floor carpet assembly with the 2 clips as shown in the illustration.

I116331


Hide 11.INSTALL FRONT SEAT ASSEMBLY RH

Hide 12.INSTALL FRONT SEAT ASSEMBLY LH

HINT:

Use the same procedure as for the LH side.


Hide 55084E 13.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116313

Engage the clamp to install the No. 1 heater to register duct sub-assembly.


b.

Install the clip.


Hide 55085 14.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116314

Engage the clamp to install the No. 2 heater to register duct sub-assembly.


b.

Install the clip.


Hide 55086A 15.INSTALL CENTER HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I115666

Engage the clamp to install the center heater to register duct sub-assembly.


b.

Install the clip.


Hide 16.INSTALL STEERING COLUMN ASSEMBLY

Hide 87211 17.INSTALL NO. 1 AIR DUCT

a.
I116312

Engage the claws to install the No. 1 air duct.


b.

Install the 2 bolts.


Hide 87245 19.INSTALL INLET HEATER WATER HOSE

a.

for M15A-FKS:

i.
I115718C02
1.583,3.219 1.677,3.469 true 0.74,2.323 1.052,2.479 0.313,0.156 10 false *a 1.406,3.115 1.719,3.271 0.313,0.156 10 false *b 1.135,1.656 1.281,1.813 0.146,0.156 10 true A 1.385,2.771 1.75,2.948 0.365,0.177 10 false *c
*a View A
*b Marking (Yellow)
*c Clip Installation Angle (120°)


Connect the inlet heater water hose with the marking (yellow) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose.




b.

for M15A-FXE:

i.
I116332C01
1.604,3.292 1.76,3.031 false 0.594,2.281 0.906,2.438 0.313,0.156 10 false *a 1.802,2.938 2.115,3.094 0.313,0.156 10 false *b 2.229,2.604 2.542,2.76 0.313,0.156 10 false *c 1.167,1.729 1.344,1.917 0.177,0.188 10 true A
*a View A
*b Marking (Yellow)
*c Clip Installation Angle (120°)


Connect the inlet heater water hose with the marking (yellow) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose.




Hide 16290F 20.INSTALL NO. 3 WATER BY-PASS HOSE ASSEMBLY

a.
I115720C02
1.729,3.469 1.844,3.188 false 0.771,2.406 1.083,2.563 0.313,0.156 10 false *a 1.896,3.104 2.208,3.26 0.313,0.156 10 false *b 1.417,2.823 1.771,2.99 0.354,0.167 10 false *c 0.823,1.354 0.969,1.5 0.146,0.146 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (120°)


for M15A-FKS:

i.

Connect the No. 3 water by-pass hose assembly with the marking (white) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the No. 3 water by-pass hose assembly.




b.

for M15A-FXE:

i.
I116333C01
1.708,3.281 1.583,3.042 false 0.198,2.292 0.51,2.448 0.313,0.156 10 false *a 1.406,2.917 1.719,3.073 0.313,0.156 10 false *b 0.833,2.667 1.146,2.823 0.313,0.156 10 false *c 0.74,1.375 0.917,1.552 0.177,0.177 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (120°)


Connect the No. 3 water by-pass hose assembly with the marking (white) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the No. 3 water by-pass hose assembly.




Hide 88716A 21.INSTALL COOLER REFRIGERANT LIQUID PIPE A

a.

Remove the vinyl tape from the cooler refrigerant liquid pipe A.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.

Compressor Oil:

for Gasoline Model:

ND-OIL 8 or equivalent

for HV Model:

ND-OIL 11 or equivalent



c.

Install the O-ring to the cooler refrigerant liquid pipe A.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the cooler refrigerant liquid pipe A.


Hide 88707 22.INSTALL SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the suction pipe sub-assembly.

Compressor Oil:

for Gasoline Model:

ND-OIL 8 or equivalent

for HV Model:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly.


e.
I115835

Rotate the hook connector as shown in the illustration.


f.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 55701J 23.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

Install outer cowl top panel sub-assembly with the 12 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
I116310

Engage the clamp.


Hide 55815E 24.INSTALL NO. 1 FRONT VENTILATOR SEAL

a.
I116309

Engage the claws to install the No. 1 front ventilator seal.


Hide 55735A 25.INSTALL WATER GUARD PLATE LH

a.
I116308

Engage the claws to install the water guarrd plate LH.


Hide 26.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 27.ADD ENGINE COOLANT

Hide 28.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 51451A 33.INSTALL CENTER ENGINE UNDER COVER