Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0422048 BRAKE BOOSTER PUMP A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP  INSTALLATION  


PROCEDURE

Hide 47070 1.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.
C430275C02
2.313,0.427 2.49,0.427 true 2.323,0.677 2.625,0.677 true 2.25,3.333 2.083,3.333 2.083,3.333 1.688,4.073 true 0.979,4.125 0.74,4.125 false 0.896,3.688 0.656,3.688 false 2.896,4.26 2.656,4.26 false 2.135,0.354 2.448,0.51 0.313,0.156 10 false *1 2.135,0.604 2.448,0.76 0.313,0.156 10 false *2 0.563,4.031 0.875,4.188 0.313,0.156 10 false *a 0.479,3.604 0.792,3.76 0.313,0.156 10 false *b 2.292,3.26 2.604,3.417 0.313,0.156 10 false *c 2.927,4.177 3.24,4.333 0.313,0.156 10 false *d
*1 Brake Booster Pump Collar
*2 Brake Booster Pump Bushing
*a Union
*b Connector
*c Wire Harness
*d Stud


Install the brake booster pump assembly, brake booster pump bushing and brake actuator case collar to the brake actuator bracket assembly.

NOTICE:
·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.

·

When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the 2 brake booster pump bushings and 2 brake booster pump collars are on the brake booster pump assembly.

·

If installing a new brake booster pump assembly, do not remove the hole plugs before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.




b.

Install the nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.
C430270N01
0.927,1.115 1.104,1.292 0.177,0.177 10 true 1 1.844,1.594 2,1.792 0.156,0.198 10 true 2

Engage the claw and clamp to install the brake booster pump assembly wire harness to the brake actuator bracket assembly.

NOTICE:

Engage the clamp and claw in the order shown in the illustration.



Hide 47381 2.INSTALL NO. 1 BRAKE TUBE CLAMP BRACKET

a.

Install the No. 1 brake tube clamp bracket to the brake booster pump assembly with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 44571A 3.INSTALL NO. 1 BRAKE ACTUATOR HOSE

a.
C430277C01
1.094,1.229 1.094,0.99 true 0.604,1.24 0.604,1 true 0.521,1.25 0.813,1.396 0.292,0.146 10 true *a 1.01,1.26 1.26,1.406 0.25,0.146 10 true *b 1.677,2.292 1.99,2.49 0.313,0.198 10 false 90° 1.688,2.948 2.073,3.135 0.385,0.188 10 false 90°
*a Identification Mark
*b Rib of Brake Booster Pump Assembly Port
V100136

Front of the vehicle


Install the No. 1 brake actuator hose to the brake booster pump assembly, and slide the clip to secure it.

NOTICE:
·

When installing the No. 1 brake actuator hose, make sure to align its alignment mark with the rib of the brake booster pump assembly.

·

Install the clip within the range shown in the illustration.




Hide 4.INSTALL BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY

a.

Temporarily install the brake actuator with brake booster pump assembly to the vehicle body with the bolt and 2 nuts.


b.
C430279

Tighten the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Do not hold the brake booster pump assembly by the connector, union or wire harness.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with brake booster pump assembly when carrying it.



HINT:

Install the brake actuator with brake booster pump assembly while avoiding the brake lines.



c.
C435062C01
0.802,1.958 1.302,1.958 1.302,1.958 0.76,1.719 true 0.031,1.052 0.229,1.26 0.198,0.208 10 false *a 1.323,1.865 1.719,2.063 0.396,0.198 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the nut.

SST
09729-00120  
09925-40010  (09925-04120)

Torque:
Specified tightening torque : 19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Do not hold the brake booster pump assembly by the connector, union or wire harness.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with brake booster pump assembly when carrying it.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.5 N*m (87 kgf*cm, 75 in.*lbf)

·

Install the brake actuator with brake booster pump assembly while avoiding the brake lines.




d.
C435063C01
0.948,2.365 0.771,2.51 0.771,2.51 1.156,2.375 true 1.49,2.708 1.75,2.917 0.26,0.208 10 true *a 0.417,2.417 0.76,2.604 0.344,0.188 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the nut.

SST
09729-00120  
09925-40010  (09925-04120)

Torque:
Specified tightening torque : 19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Do not hold the brake booster pump assembly by the connector, union or wire harness.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with brake booster pump assembly when carrying it.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.5 N*m (87 kgf*cm, 75 in.*lbf)

·

Install the brake actuator with brake booster pump assembly while avoiding the brake lines.




e.

Engage the clamp to install the wire harness to the brake actuator bracket assembly.


f.

Engage the clamp to install the wire harness to the brake actuator bracket assembly.


g.

Connect the connector.


h.
C430259C01
1.042,1.469 1.313,1.021 true 2.135,1.646 2,1.375 true 2.573,0.885 2.26,0.99 true 2.333,0.385 2.031,0.844 true 1.656,0.167 1.792,0.719 true 1.229,0.344 1.531,0.615 true 0.938,1.479 1.177,1.688 0.24,0.208 10 true *a 2.042,1.656 2.281,1.854 0.24,0.198 10 true *b 2.594,0.781 2.854,0.99 0.26,0.208 10 true *c 2.281,0.167 2.5,0.365 0.219,0.198 10 true *d 1.573,0 1.76,0.198 0.188,0.198 10 true *e 1.042,0.26 1.271,0.49 0.229,0.229 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.


i.

Engage the clamp to install the brake line.


j.
C430284C01
1.76,2.927 2.073,3.083 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, fully tighten the 6 brake lines.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




k.
C430285C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.




l.
C430286C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.




Hide 473A1 5.INSTALL ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.

Temporarily tighten the accumulator to brake master cylinder tube to the brake booster pump assembly.


b.

Install the accumulator to brake master cylinder tube with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.
C430288C01
1.771,2.927 2.083,3.083 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, tighten the accumulator to brake master cylinder tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow the accumulator to brake master cylinder tube to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 44571A 6.INSTALL NO. 1 BRAKE ACTUATOR HOSE

a.
C430290C01
1.427,0.833 1.594,1.177 true 1.323,0.625 1.521,0.833 0.198,0.208 10 true *a 1.688,2.958 2.146,3.156 0.458,0.198 10 false 90° 1.677,2.281 2.135,2.479 0.458,0.198 10 false 90°
*a Identification Mark
V100136

Front of the vehicle


Connect the No. 1 brake actuator hose to the No. 1 brake actuator tube to install it, and slide the clip to secure it.

NOTICE:
·

Make sure to connect the No. 1 brake actuator hose with its identification mark facing the front of the vehicle.

·

Install the clip within the range shown in the illustration.




Hide 44551C 7.BLEED NO. 1 BRAKE ACTUATOR TUBE

Hide 821H1 9.INSTALL HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Install the HV floor under wire to the vehicle body with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide G9200 10.INSTALL INVERTER WITH CONVERTER ASSEMBLY