Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › INVERTER WITH CONVERTER › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0424580 INVERTER WITH CONVERTER A

HYBRID / BATTERY CONTROL  INVERTER WITH CONVERTER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 3 wire harness clamp brackets to the inverter with converter assembly with the 3 bolt.

A461161N01
1.844,0.375 2,0.573 0.156,0.198 10 true A 5.177,0.948 5.333,1.146 0.156,0.198 10 true A 6.135,1.104 6.292,1.302 0.156,0.198 10 true B

Torque:
Bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)

Torque:
Bolt B : 9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide G9214 2.INSTALL NO. 1 INVERTER BRACKET

a.

Temporarily install the No. 1 inverter bracket to the hybrid vehicle transaxle assembly with the bolt and 2 nuts.

NOTICE:

Make sure that the inverter with converter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket.


HINT:

If the bolts and nuts are not tightened appropriately, the inverter with converter assembly may make an abnormal noise.



b.
A464222N01
2.583,1.656 2.823,1.906 0.24,0.25 10 true A 2,1.656 2.24,1.906 0.24,0.25 10 true B 1.063,1.677 1.302,1.927 0.24,0.25 10 true B

Fully tighten the bolt (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

Fully tighten the 2 nuts (B).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


d.

Set the inverter with converter assembly on hybrid vehicle transaxle assembly.

NOTICE:
·

When installing the inverter with converter assembly, be careful not to damage the parts around it.

·

To prevent damage, do not hold the inverter with converter assembly by the connectors, brackets or cooling pipes.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·
A406201C03
0.625,2.229 0.802,2.427 0.177,0.198 10 true *a 0.625,3.365 0.813,3.542 0.188,0.177 10 true *b
*a Correct
*b Incorrect


Make sure that the inverter with converter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket



HINT:

If the bolts and nuts are not tightened appropriately, the inverter with converter assembly may make an abnormal noise.



Hide G9215 3.INSTALL NO. 2 INVERTER BRACKET

a.

Temporarily install the No. 2 inverter bracket to the hybrid vehicle transaxle assembly with the 4 bolts.


b.
A464221N01
0.75,1.833 1,2.083 0.25,0.25 10 true A 1.698,1.875 1.948,2.125 0.25,0.25 10 true B 2.031,1.865 2.281,2.115 0.25,0.25 10 true B 2.396,1.844 2.646,2.094 0.25,0.25 10 true B

Fully tighten the bolt (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

Fully tighten the 3 bolts (B).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide G9200 4.INSTALL INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Wear insulated gloves.


a.

Temporarily install the inverter with converter assembly with the 4 bolts.


b.

Fully tighten the 2 bolts in the order shown in the illustration to the inverter with converter assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

A460044E01
2.042,0.906 2.198,1.104 0.156,0.198 10 true 1 2.792,0.896 2.948,1.094 0.156,0.198 10 true 2 3.74,1.552 3.896,1.75 0.156,0.198 10 true 1 4.948,1.563 5.104,1.76 0.156,0.198 10 true 2


c.

Fully tighten the 2 bolts in the order shown in the illustration to the inverter with converter assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide G921E 5.INSTALL INVERTER PROTECTOR

a.
A464135N01
2.333,1.802 2.49,2 0.156,0.198 10 true 1 0.479,0.333 0.635,0.531 0.156,0.198 10 true 2

Temporarily install the inverter protector with the 2 bolts.


b.

Fully tighten the 2 bolts in the order shown in the illustration to the inverter with converter assembly.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide G1148 6.CONNECT MOTOR CABLE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.

Temporarily connect the motor cable to the inverter with converter assembly with the 4 bolts.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.




b.
A464132C02
0.875,0.219 1.188,0.219 1.188,0.219 1.469,0.521 true 0.698,0.104 1.01,0.302 0.313,0.198 10 false *a 2.958,1.854 3.115,2.052 0.156,0.198 10 true A 0.208,1.938 0.385,2.125 0.177,0.188 10 true 2 0.677,2.813 0.865,3.01 0.188,0.198 10 true 1 2.667,2.448 2.833,2.635 0.167,0.188 10 true 3
*a Waterproof Seal


Fully tighten the bolt (A).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Fully tighten the 3 bolts in the order shown in the illustration to connect the motor cable to the inverter with converter assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.
A464131

Temporarily install the 6 bolts.

NOTICE:
·

To prevent the threads from being damaged, temporarily tighten the 6 bolts by hand.

·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.




e.

Using an insulated tool, fully tighten the 6 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

·

Be sure to use a torque wrench to tighten the bolts.




Hide G9221A 7.INSTALL UPPER INVERTER COVER

CAUTION:

Wear insulated gloves.


a.

Install the upper inverter cover to the inverter with converter assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Visually confirm that the inverter cover waterproof seal is securely installed before installing the upper inverter cover.

·

Do not touch the waterproof seal of the upper inverter cover.

·

Make sure that the interlock is fully engaged.

·

Do not damage the terminals, interlock connector or inverter with converter assembly during installation.

·

Do not allow any foreign matter or water to enter the inverter with converter assembly.

·
A464129C02
2.083,2.146 2.656,1.635 2.656,1.635 2,1.458 false 1.031,0.313 1.302,0.313 1.302,0.313 1.781,0.917 true 0.854,0.188 1.167,0.385 0.313,0.198 10 false *a 2.698,1.521 3.01,1.719 0.313,0.198 10 false *1
*1 Inverter Cover
*a Screw


Do not remove or excessively tighten the screw of the upper inverter cover.

·

Although the upper inverter cover may feel loose, this is not due to a malfunction.

·
A459828C01
1.521,1.719 1.74,1.896 0.219,0.177 10 true *a
*a No Gap


Push in the upper inverter cover until it contacts the inverter with converter assembly.




Hide G922AA 8.CONNECT INLET NO. 1 INVERTER COOLING HOSE

a.
A464213C01
0.76,0.896 0.49,0.448 true 1.292,0.885 1.042,0.375 true 0.333,0.271 0.646,0.469 0.313,0.198 10 false *a 0.875,0.219 1.188,0.417 0.313,0.198 10 false *b 1.083,1.49 1.396,1.688 0.313,0.198 10 false *c 2.302,0.063 2.615,0.26 0.313,0.198 10 false *d 3,0.813 3.313,1.01 0.313,0.198 10 false *e 2.646,0.292 3.031,0.531 0.385,0.24 10 false 120°
*a Alignment Mark (Green)
*b Rib
*c 2 to 5 mm (0.0787 to 0.197 in.)
*d Up
*e LH Side


Connect the inlet No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:

To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.


HINT:
·

Make sure that the clip is positioned as shown in the illustration.

·

Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.




Hide G922C 9.CONNECT OUTLET NO. 1 INVERTER COOLING HOSE

a.
A464214C01
0.76,0.885 0.542,0.406 true 1.281,0.875 1.063,0.396 true 0.417,0.219 0.729,0.375 0.313,0.156 10 false *a 0.958,0.208 1.271,0.365 0.313,0.156 10 false *b 1.083,1.479 1.396,1.635 0.313,0.156 10 false *c 2.302,0.063 2.615,0.219 0.313,0.156 10 false *d 3,0.833 3.313,0.99 0.313,0.156 10 false *e 2.635,0.271 3.25,0.469 0.615,0.198 10 false 120°
*a Alignment Mark (Blue)
*b Rib
*c 2 to 5 mm (0.0787 to 0.197 in.)
*d Up
*e LH Side


Connect the outlet No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:

To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.


HINT:
·

Make sure that the clip is positioned as shown in the illustration.

·

Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.




Hide 82121 10.INSTALL ENGINE WIRE

CAUTION:

Wear insulated gloves.


a.
A464125

Engage the clamp and connect the engine wire to the inverter with converter assembly.


b.

Temporarily install the nut.

NOTICE:

To prevent the threads from being damaged, temporarily tighten the nut by hand.



c.

Fully tighten the nut.

Torque:
10 N*m (102 kgf*cm, 89 in.*lbf)


d.

Engage the 2 claws to close the engine wire terminal cover.


e.
A464123

Connect the engine wire to the inverter with converter assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 89 in.*lbf)


f.

Engage the clamp.


g.
A464219

Engage the 2 clamps.


h.

Connect the 3 connectors.


i.

Connect the engine wire to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


j.
A464122N01
2.073,0.521 2.313,0.771 0.24,0.25 10 true A 0.719,0.792 0.958,1.042 0.24,0.25 10 true B 1.438,0.333 1.677,0.583 0.24,0.25 10 true A 1.333,1.094 1.573,1.344 0.24,0.25 10 true A 0.75,2.875 0.99,3.125 0.24,0.25 10 true B

Engage the 2 clamps (B).


k.

Connect the engine wire to the inverter with converter assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


l.

Engage the 3 clamps (A) and connect the No. 1 fuel vapor feed hose.


m.
A464217

Connect the inverter with converter assembly connector and move the lock lever to lock them.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connectors.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.




Hide 25860 11.INSTALL PURGE VALVE (PURGE VSV)

Hide 12.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the inverter with converter assembly with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 55701J 13.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55815E 15.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 16.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 821H2 17.CONNECT HV AIR CONDITIONING WIRE

CAUTION:

Wear insulated gloves.


a.

Engage the clamp.


b.
A464116

Connect the HV air conditioning wire to the inverter with converter assembly and install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Do not allow any foreign matter or water to enter the inverter with converter assembly.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.




Hide 821H1 18.CONNECT FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


a.

Engage the 2 clamps.


b.
A466081

Connect the HV floor under wire to the inverter with converter assembly and install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Do not allow any foreign matter or water to enter the inverter with converter assembly.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.




Hide 82121 19.CONNECT ENGINE WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.

Engage the 2 clamps.


b.
A464216

Connect the inverter with converter assembly connector and move the lock lever to lock them.

NOTICE:
·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.

·

Do not touch the waterproof seal or terminals of the connectors.




Hide 21.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.

Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly.

NOTICE:

Align the cutout of the air cleaner hose assembly with the protrusion of the throttle body with motor assembly.



b.

Tighten the hose clamp.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


c.

Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.


d.

Engage the 3 grommets and pin to install the air cleaner assembly with air cleaner hose.


e.

Engage the wire harness clamp.


f.

Connect the connector.